KYMCO 2006 MXU 500 Off-Road Скачать руководство пользователя страница 166 | Manualshive

Страница: 166 / 677

background image

4. Remove the battery

And store it in

an area protected from freezing temperatures
and direct sunlight and out of the reach of
children, slow charge the battery once a
month.

(page 147)

5. Wash and dry the ATV, and wax all painted

surfaces.

6. Inflate the tires to their recommended

pressures.

7. Place the ATV on blocks to raise all four tires

off the ground.

3. Remove the spark plug and pour one

tablespoon (15 - 20 cc)of clean engine oil into
the cylinder. Operate the starter for a few
seconds to distribute the oil, then reinstall the
spark plug.

POTENTIAL HAZARD
Prolonged contact of fuel with the skin.
Breathing fuel vapor.

WHAT CAN HAPPEN
The fuel can cause skin irritation.
Fuel vapor could cause lung damage.

HOW TO AVOID THE HAZARD
Avoid repeated or prolonged contact of fuel
with the skin or breathing of fuel vapor.

KEEP OUT OF REACH OF CHILDREN.

POTENTIAL HAZARD
Allowing open flames or sparks near the
battery.

WHAT CAN HAPPEN
Gases may explode and possibly cause
injury.

HOW TO AVOID THE HAZARD
Do not allow open flames or sparks near the
battery.

156

WARNING

WARNING

«
...
164
165
166
167
168
...
»

Содержание 2006 MXU 500 Off-Road






































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2006 MXU 500 Off-Road

Бренд: Yamaha Страницы: 26

Бренд: BOMBARDIER Страницы: 20

Бренд: TrailMaster Страницы: 8

Бренд: TrailMaster Страницы: 40

Бренд: TrailMax Страницы: 62

Бренд: Dinli Страницы: 122

Бренд: Wintex Agro Страницы: 9

Бренд: Lynx Страницы: 196

Бренд: Kärcher Страницы: 16

MIC 45 advanced

Бренд: Kärcher Страницы: 19

Бренд: Kinroad Страницы: 38

Бренд: Monzana Страницы: 13

Бренд: Global Страницы: 11

Бренд: Racing Страницы: 17

Бренд: E-Z-GO Страницы: 78

Бренд: KAYO MOTOR Страницы: 99

Sasquatch Youth 800W

Бренд: Daymak Страницы: 24

Бренд: Yamaha Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды