Kverneland EDW2 Скачать руководство пользователя страница 81

Страница: 81 / 89

8. Electrical hopper cover

The electrical hopper cover (tarpaulin) is an option on the bigger spreader range

The maximum opening and closing position can be adjusted by the screw on the motor:
1. Remove the 2 stainless steel screws. These screws are plugs to prevent water and dirt can

enter the motor.

2. After removing the plugs the motor can be adjusted by 2 screws (Allen key number 4)
• The top screw is for adjusting the maximum closing position

By turning clock wise the cover will close further
By turning anti clockwise the cover will close less far

• The bottom screw is for adjusting the maximum opening position

By turning clock wise the cover will open further
By turning anti clockwise the cover will open less far

At the maximum closing and opening position there should be a little tension on the cover itself.

Adjustment for closing

Adjustment for opening

8.1 Adjustments

Содержание EDW2


























































































Результаты поиска

Содержание EDW2

Отзывы:

Kverneland EDW2, Руководство пользователя, Страница: 81 / 89

Результаты поиска

Содержание EDW2

Отзывы: