Kverneland EDW2 Скачать руководство пользователя страница 58

Страница: 58 / 89

4. Calibrations

Special steel
connection
plates

Reference sensor

load cells 10 ton

4.4 Hopper calibration: RO-M EW CL-EW

(Pincode 8)

The Pin 8 calibration has to be done after changing a PCB, weight sensor or reference sensor.

During this calibration the following 5 steps will be done during this calibration

The empty weight of the hopper

The corresponding load cell value for an empty hopper

The value of the reference sensor will be stored when machine is standing flat.

The machine will store the value of the weight cell when the hopper is filled with a fixed weight

The machine will store the value of the reference sensor under an angle.

Due to the difference in construction between the 1 load cell and 4 load cell machines the calibration
has a few additional steps
For a good and successful Pin 8 calibration please follow the steps one the next pages

Содержание EDW2


























































































Результаты поиска

Содержание EDW2

Отзывы:

Kverneland EDW2, Руководство пользователя, Страница: 58 / 89

Результаты поиска

Содержание EDW2

Отзывы: