Kustom Signals Raptor RP-1 Скачать руководство пользователя страница 57

Страница: 57 / 93

SECTION 7—OPERATION

If on the other hand the unit is not in Hold for the typical

amount of time (less than one second), the region around

the saved patrol will be excluded from the initial patrol

search.

Example: The patrol vehicle is traveling 25 MPH, there is

a strong approaching target traveling 45 MPH, and the

radar has mistakenly combined the two and is displaying 70

MPH for patrol. The operator can quickly go in and out of

Hold to reject the region around 70 MPH and the correct 25

MPH patrol speed will be displayed.

7.7 MENU SCREEN MODES

The Raptor RP-1 has a graphical LCD display panel. This

allows the operator to make operational and configuration

options setup selection using full text menu screens.

7.7.1 MAIN MENU SCREEN

The highest level of the menu screens is the main menu. To

get the main menu press the Menu (

) switch. To select

one of the menu options, use the Up and Down switches to

highlight the option and then press the Enter (

) switch.

7.15

Содержание Raptor RP-1






























































































Результаты поиска

Содержание Raptor RP-1

Отзывы:

Похожие инструкции для Raptor RP-1

Бренды по названию

Популярные бренды

Kustom Signals Raptor RP-1, Руководство оператора

Результаты поиска

Содержание Raptor RP-1

Отзывы:

Похожие инструкции для Raptor RP-1

Бренды по названию

Популярные бренды