KUST Elektronik PT5040 Скачать руководство пользователя страница 9

Страница: 9 / 87

Differential

PT5040 Operation Manual Chapter 2 General specifications

Beeper alarm

Beep mode

ON (adjust for high and low tone), OFF

Memory

Built-in memory: 100 files

USB disk memory

Interface

HANDLER (START, STOP, PASS, NG, BUSY, EOC, etc.)

RS232C USB Device USB Host LAN

Comparison methods

Area size comparison

As shown in figure 2-1, when comparison method is set to AREA SIZE, the area sizes of both

standard waveform and the tested waveform are calculated (integration method) between A and

B. The percent deviation is the ratio of the area size difference to the area size of the standard

waveform between A and B, expressed as a percentage.

Figure 2-1 Area Size Comparison

The area size of the waveform is nearly proportional to the energy loss in the winding. When a

sample winding has a short circuit between layers, the short circuit area is reflected as an

increase of energy loss.

area comparison

When comparison method is set to Differential Area, PT50xx calculates the area size of

differential portion between the standard waveform and the tested waveform from A to B. (The

differential portion area size is indicated as the shaded part in Figure 2-2.) The percent deviation

is the ratio of the differential portion area size to the area size of the standard waveform between

A and B, expressed as a percentage.

2-2

Содержание PT5040
























































































Результаты поиска

Содержание PT5040

Отзывы:

Бренды по названию

Популярные бренды

KUST Elektronik PT5040, Руководство по эксплуатации

Результаты поиска

Содержание PT5040

Отзывы:

Бренды по названию

Популярные бренды