KUST Elektronik PT5040 Скачать руководство пользователя страница 33

Страница: 33 / 87

three

supports

instrument

the

Although



Note:

PT5040 Operation Manual Chapter 6 Introduction to [SYSTEM]

can exit the operation of creating. Letters from A to Z, numbers from 0 to 9,

and underline, etc. can be used for a file name.



Note: Users are recommended to use self-defined folder name. The

default name ranges from FOLDER01 to FOLDER 99.

Save

Press this key to save a file. Move the arrow key to choose the catalog

storing the file. Press the Save soft key and then enter the file name.

➢

Press ENTER to end this operation. If the ENTER button is pressed without

inputting the file name, the default name is FILExxx.STA (xxx ranges from

001 to 999.).

➢

Press . , soft keys .STA, .TXT and .CSV will be displayed in the soft key

zone.

◆

Press .STA, the file will be save as .STA file. If the file name is not

input, the file will be named as the default name FILExxx. STA (xxx

ranges from 001 to 999.).

◆

Press .TXT, the file will be save as .TXT file. If the file name is not

input, the file will be named as the default name FILExxx. TXT (xxx

ranges from 001 to 999.).

◆

Press .CSV, the file will be save as .CSV file. If the file name is not

input, the file will be named as the default name FILExxx. CSV (xxx

ranges from 001 to 999.).



Note: Users are recommended to use self-defined folder name. The

default name ranges from FOLDER001 to FOLDER 099.

Load

Load a file saved in an external U disk. Using the arrow key can choose the

desired file. Press Load. If the selected external file is needed to load to the

internal RAM, press YES, otherwise NO.

file

formats, .STA, .TXT and CSV, only .STA file can be loaded to internal

RAM.

Delete

Delete saved files. Press Delete. Then choose YES to delete the file,

otherwise NO to cancel the delete operation.

Copy to I: Copy external files (in U disk) to internal file list. Using the arrow key can

select the desired file. If the selected file is needed to copy to the internal file

list, press Copy to I: and then choose YES, otherwise choosing NO to give

up this operation. Press ENTER to end coping. In numeric input state, press

ESC to exit from this page.

5-11

Содержание PT5040
























































































Результаты поиска

Содержание PT5040

Отзывы:

Бренды по названию

Популярные бренды

KUST Elektronik PT5040, Руководство по эксплуатации

Результаты поиска

Содержание PT5040

Отзывы:

Бренды по названию

Популярные бренды