Kuhnke 610.441.31 Скачать руководство пользователя страница 20

Страница: 20 / 56

KUHNKE Automation

E 774 GB

30.06.2014

5.3 Device with EtherCAT® Fieldbus Port, X7, X8

5.3.1 EtherCAT® Fieldbus Port X7, X8

Connector X7/X8/

wiring:

X7/X8

PIN

Function

RJ45

TX+

TX-

RX+

75 Ohm

RX-

75 Ohm

5.3.2 Device and EtherCAT® Status

5.3.2.1 "EtherCAT®" LED (RUN/ERROR)

The LED labelled "EtherCAT®" indicates the state of the EtherCAT® ASIC.

State

LED flash code

Explanation

Init

Red, on

Initialising, no data exchange

Pre-Op

Red/green, 1:1

Pre-operational, no data exchange

Safe-Op

Red/green, 3:1

Safe operation, inputs readable

Green, on

Operational, unrestricted data exchange

5.3.2.2 "POWER" LED

State

LED flash code

Explanation

5.3.2.3 LED "BUS IN" , LED "BUS OUT"

The "In" and "Out" LEDs indicate the physical state of the Ethernet port they
are allocated to.

State

LED flash code

Explanation

Not connected

Off

No Ethernet connection

Connected

Green, on

Connected to Ethernet

Traffic

Green, flashing

Exchanging telegrams

OUT

Содержание 610.441.31

























































Результаты поиска

Содержание 610.441.31

Отзывы:

Бренды по названию

Популярные бренды

Kuhnke 610.441.31, Инструкция по эксплуатации

Результаты поиска

Содержание 610.441.31

Отзывы:

Бренды по названию

Популярные бренды