KUHN GMD602 GII Скачать руководство пользователя страница 58

Страница: 58 / 64

Disc mower

GMD602 GII

Trouble shooting guide

Not possible to place the

machine in "headland turn"
position.

The hydraulic circuit had not

been pressurized correctly
before attempting to place the
machine in headland turn
position.

The 2 hydraulic hoses of the

transport/work position
cylinder are connected to a
double acting valve with float
position.

Open the hydraulic valve using

the 18mm box spanner
supplied with the machine

Shift the tractor hydraulic valve

in the direction for placing the
machine in working position, to
pressurize the circuit
93 bar (1348 psi).

Shut-off the hydraulic valve.

Shift the tractor's hydraulic
valve in float position. The
pressure on the gauge drops.

Repeat previous operations

several times until pressure
stays at 93 bar (1348 psi).

Содержание GMD602 GII

































































Результаты поиска

Содержание GMD602 GII

Отзывы:

Похожие инструкции для GMD602 GII

Бренды по названию

Популярные бренды

KUHN GMD602 GII, Руководство оператора

Результаты поиска

Содержание GMD602 GII

Отзывы:

Похожие инструкции для GMD602 GII

Бренды по названию

Популярные бренды