KUHN GMD602 GII Скачать руководство пользователя страница 57

Страница: 57 / 64

Trouble shooting guide

Disc mower

GMD602 GII

TROUBLE SHOOTING GUIDE

Problem

Cause

Remedy

Uneven stubble.

Dull or broken knives.

Replace knives.

Knives not installed correctly.

Make sure the arrow on the

knife upper face is pointing in
the disc's direction of rotation.

Too low PTO speed (rotational

frequency).

Increase speed to 540 min

-1

Soil build up in front of the

cutterbar.

Too much cutterbar down

pressure.

Increase accumulator

pressure.

Very wet working conditions.

Adjust main frame height with

regards to the ground.

Bad ground contour

adaptation.

Incorrect main frame setting.

Adjust main frame height with

regards to the ground.

Excessive ground speed.

Reduce ground speed.

Insufficient ground pressure.

Reduce accumulator pressure.

Insufficient cutterbar ground

clearance in "headland turn"
position.

Incorrect tractor lift linkage

setting.

See machine attachment.

Too long levelling rod

adjustment.

Shorten levelling rods.

Excessive mowing-

conditioning unit lateral
oscillation in transport position.

Incorrect transport stop

adjustment.

Readjust transport stop.

Содержание GMD602 GII

































































Результаты поиска

Содержание GMD602 GII

Отзывы:

Похожие инструкции для GMD602 GII

Бренды по названию

Популярные бренды

KUHN GMD602 GII, Руководство оператора

Результаты поиска

Содержание GMD602 GII

Отзывы:

Похожие инструкции для GMD602 GII

Бренды по названию

Популярные бренды