KUHN GMD 3150 TL CE Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 68

background image

4. - Safety

GMD 3150/3550/4050 TL CE

13

7N136AGB-A

Disk mower



Precautions for maintenance and repair

work

Before leaving the tractor or before adjusting,
maintaining or repairing the machine, always
perform the safety shutdown procedure.

Rest the machine on the ground, release the
pressure from the hydraulic circuit and leave the
machine to cool down.

Make sure that the parts of the machine that need to
be lifted for maintenance or repair work are firmly
propped up.

Before any work is done on the electric circuit or
before any electric welding is carried out on the
attached machine, disconnect the machine from the
tractor electrical circuit. Also disconnect alternator
and battery terminals.

Repairs on elements under pressure or tension
(springs, pressure accumulators, etc.) must only be
carried out by competent persons with regulation
equipment.

Wear appropriate protective clothing (gloves,
shoes, goggles, hearing protection, etc.).

Do not solder, weld or use a blow torch near fluids
under pressure or inflammable products.

For your own safety and for correct machine
operation, only use original manufacturer parts.

It is strongly recommended to have your machine
checked by your Kuhn dealer after each season,
especially tools and their attaching hardware.

«
...
13
14
15
16
17
...
»

Содержание GMD 3150 TL CE





































































Отзывы:

Нет отзывов

Похожие инструкции для GMD 3150 TL CE

Бренд: NARGESA Страницы: 50

AJSPD850P - P2 DECK

Бренд: Panasonic Страницы: 73

Бренд: FEAS Страницы: 72

Бренд: Hagie Страницы: 141

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 20

Бренд: Gainsborough Страницы: 2

Бренд: Gainsborough Страницы: 2

Бренд: Gait up Страницы: 12

Бренд: Gait up Страницы: 6

Бренд: Gaiam Страницы: 2

Бренд: Garmin Страницы: 12

Бренд: Garmin Страницы: 13

Бренд: Parkside Страницы: 2

Бренд: Park House Healthcare Страницы: 12

Бренд: Radial Engineering Страницы: 2

Бренд: Radial Engineering Страницы: 2

Бренд: ABB Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды