background image

 

 
 

       

Safety Information     

 

 

Observe these precautions at all times. 
 

Propeller

 

People  can  be  injured  or  killed  if  they  come  in 
contact  with  the  propeller.  The  propeller  can  keep 
moving 

even 

when 

the 

motor 

is 

in 

neutral,  and  sharp  edges  of  the  propeller  can  cut 
even when stationary. 
Stop the engine when a person is in the  
water near you. 
Keep people out of reach of the propeller,  even 
when the engine is off. 

Rotating parts

 

Hands,  feet,  hair,  jewelry,  clothing,  straps,  etc. 
can become entangled with internal rotating parts of 
the engine, resulting in serious injury or death. 
Keep  the  top  cowling  in  place  whenever 
possible.  Do  not  remove  or  replace  the  cowling 
with the engine running. 
Only  operate  the  engine  with  the  cowling  
removed according to the specific instructions in  the 
manual.  Keep  hands,  feet,  hair,  jewelry,  clothing, 
straps, etc. away from any exposed moving parts. 

Hot parts

 

During  and  after  operation,  engine  parts  are  hot 
enough  to  cause  burns.  Avoid  touching  any parts 
under 

the 

top 

cowling 

until 

the  

engine has cooled. 

Electric shock

 

Do  not  touch  any  electrical  parts  while  starting  or 
operating  the  engine.  They  can  cause  shock  or 
electrocution. 

    

Engine shut-off cord (lanyard) 

Attach  the  engine  shut-off  cord  so  that  the  
engine  stops  if  the  operator  falls  overboard  or 
leaves the helm. This prevents the boat from  

 

 

running  away  under  power  and  leaving  people 
stranded,  or  running  over  people  or  objects. 
Always  attach  the  engine  shut-off  cord  to  a 
secure place on your  clothing or your  arm or  leg 
while  operating.  Do  not  remove  it  to  leave  the 
helm  while  the  boat  is  moving.  Do  not  attach the 
cord to clothing that could tear loose,  or  route  the 
cord  where  it  could  become  entangled, 
preventing it from functioning. 
Do  not  route  the  cord  where  it  is  likely  to  be 
accidentally  pulled  out.  If  the  cord  is  pulled 
during operation, the engine will shut off and  you 
will  lose  most  steering  control.  The  boat  could 
slow  rapidly,  throwing  people  and  objects 
forward. 

Gasoline

 

Gasoline  and  its  vapors  are  highly  flammable 
and explosive. 

Gasoline exposure and spills

 

Take  care  not  to  spill  gasoline.  If  gasoline 
spills,  wipe  it  up  immediately  with  dry  rags. 
Dispose of rags properly. 
If  any  gasoline  spills  onto  your  skin,  immediately 
wash  with  soap  and  water.  Change  clothing  if 
gasoline spills on it. 
If  you  swallow  gasoline,  inhale  a  lot  of  gasoline 
vapor,  or  get  gasoline  in  your  eyes,  get 
immediate  medical  attention.  Never  siphon  fuel 
by mouth. 

 

Carbon monoxide

 

This  product  emits  exhaust  gases  which  contain 

carbon  monoxide,  a  colorless,  odorless  gas 

which  may  cause  brain  damage  or  death  when 

inhaled.  Symptoms  include  nausea,  dizziness, 

and  drowsiness.  Keep  cockpit  and  cabin  areas 

well ventilated.  Avoid blocking exhaust outlets. 

 

Содержание MOTOR6



















































































Отзывы: