Kubota DMC 8028 Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 219

background image

Parking and Storage

100

Storage

At the end of the season, the machine should be prepared for storage:
Carry out the following:

•

Clean the machine thoroughly.

→

»Cleaning« Page 96

•

Change the oil in all the machine's transmissions.

→

»Lubricants« Page 216

•

The hydraulic quick coupling should either be covered with a dust
cap or placed in a small plastic bag.

•

The P.T.O. shaft should be cleaned, oiled and stored somewhere
dry so as to avoid damage or corrosion.

•

Always check that the machine's safety equipment is not worn or
damaged.

•

Always park the machine with the cutting unit lowered and its
wheels on the ground.

If the machine's cutting unit is parked in the raised position for a
prolonged period, there is a risk that the cutting unit may sink unevenly
in the machine's hydraulic cylinder. This will cause problems when the
machine's hydraulic system is coupled to the tractor.

→

»Checking the cutting unit« Page 55

•

Bleed as much excess hydraulic pressure from the cylinders and
hoses as possible.

•

Place the machine in a ventilated machine room.

•

Both of the machine's wheel axles should be supported on blocks
so that the wheels are lifted off the ground.

Safety

\

WARNING

The machine shall be secured when parked

The machine must be correctly secured when parked in storage.
A correctly secured machine prevents persons from being run
over and other serious accidents.
If the machine is not properly secured when parked it can result in
serious injuries and death.

Therefore, when disconnecting make sure that:

•

The machine is placed upon a horizontal and level surface.

•

The P.T.O. is disengaged.

•

Lower the implement to the ground.

•

The hydraulic controls is in neutral.

•

The tractor is stopped.

•

The ignition key is removed.

•

The parking brake is set.

•

The tractor cannot roll after being disconnected.

•

Children and unauthorized persons must never be allowed
near the machine.

Failure to secure the tractor to prevent it from rolling could
endanger lives.

«
...
98
99
100
101
102
...
»

Содержание DMC 8028




























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DMC 8028

Бренд: ICS Schneider Messtechnik Страницы: 124

Бренд: Baroness Страницы: 40

Бренд: Baroness Страницы: 40

Бренд: BARKO LOADERS Страницы: 85

Бренд: Cameo Страницы: 64

Бренд: Cameo Страницы: 100

Бренд: CAME Страницы: 32

Бренд: Tactile Medical Страницы: 23

Бренд: Taarup Страницы: 72

FLEX-FOOT ASSURE

Бренд: Össur Страницы: 82

Бренд: Össur Страницы: 32

Digital Measuring System forUnloader & CTi CM...

Бренд: Össur Страницы: 6

DH Offloading Post-Op StyleShoe

Бренд: Össur Страницы: 32

Бренд: Össur Страницы: 65

Бренд: Össur Страницы: 92

Бренд: Össur Страницы: 38

LUNAQUA Classic LED

Бренд: Oase Страницы: 16

Бренд: Kelvin Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды