manualshive.com logo in svg

Kubota B2791A, Руководство оператора и каталог запасных частей

Поделиться
Скачать
Kubota B2791A Скачать руководство пользователя страница 15

ASSEMBLY 

OM 0336QH-A 

13

5 1/8"

Figure 4a

B2792 

F

OR 

T

RACTORS 

B3030 WITHOUT

 

C

AB

 

B2630  - B2710 - B2910, B3200 

AND 

B7800 

7B

7A

2

4

4

4

6

6

5

1

9

2

5

3

1

7

8

Installing the PTO Drive Kit B2792 (Optional

)  

(Figure 4a)

1. 

Install a 1/4" NF grease fitting (item 1) on each 
1" flange bearing (item 2).  Place the flange 
bearing on each subframe cross plate (item 9) 
as shown making sure to point the bearing's 
grease fitting upward as illustrated.  

2. 

Slide the 1" output shaft (item 3) inside each 
flange bearing making sure to direct the longest 
splined end towards the rear of the subframe 
and to install the bearings in the correct 
position.  

3. 

Secure each flange bearing with the 

5/8"NC x 1 3/4" lg hex bolts (item 4), 

5/8" 

lockwashers (item 5) and 

5/8"NC nylon 

insert locknuts (item 6) as illustrated on 
figure 4.  Tighten at 165 lbs-pi or 224 N-M. 

4. 

Position the output shaft so that it exceeds 
the rear cross plate by 5 1/8".  Apply 
threadlocker on the bearing setscrews and 
tighten securely.  Then grease each flange 
bearing. 

5. 

After the subframe is mounted on the tractor 
(see following pages for the procedure) 
attach the longest yoke of the fixed driveline 
(item 7A) to the output shaft (item 3). Attach 
the driveline's quick connect yoke (item 7B) 
to the tractor's mid PTO. 

IMPORTANT: In order to avoid damaging 
the fixed driveline (item 7) remove it when 
using the blade. 

 

6. 

The driveline's male half (item 8) must be 
installed when mounting the snowblower or the 
rotary broom but it's not required when using 
the blade. 

  

WARNING: 

To avoid serious 

personal injury: Make sure that the quick 
coupler is securely locked in place. A 
"click" must be heard. 

  

WARNING

: The driveline can be 

damaged and could cause serious 
personal injury if the quick hitch is not 
attached properly.

 

IMPORTANT: In order to avoid damaging 
the driveline kit components, do not raise 
or lower the snowblower when blowing 
snow.  This should only be done when the 
snowblower is idle. 

Содержание B2791A













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды