Kubota AP-SD96 страница 14 Скачать руководство пользователя

Страница: 14 / 36

Section 1: Optional Equipment & Set-up

AP-SD96 Silage Defacer 350-270MK

9/3/19

Table of Contents

Hitch Assembly Options

Kubota offers two hitch options for the Silage Defacer. To

be compatible with this attachment, skid steers, track

loaders, and tractors must have a front loader equipped

with a quick attach hitch plate or Euro hitch plate.

Quick Attach Hitch . . . . . . . . . . . . . . . . . . . 350-260A
Euro Hitch . . . . . . . . . . . . . . . . . . . . . . . . . . 350-239A

DANGER

To avoid serious injury or death:

•

Always secure equipment with solid, non-concrete supports

before working under it. Never go under equipment

supported by concrete blocks or hydraulics. Concrete can

break, hydraulic lines can burst, and/or hydraulic controls

can be actuated even when power to hydraulics is off.

•

Keep all persons and objects clear while any part of the

machine is in motion. A person can be pinched or crushed

by the machine.

Refer to

Figure 1-1:

1. On a flat surface, place solid, non-concrete supports

under the left and right arm of rotor frame (#2).

Ensure rotor frame (#2) is level to the ground.

2. While wearing gloves, use a rag to wipe down the

face of all mounting plates (#7 & #8) to clear away

debris.

3. Using a hoist or power machine, lift hitch

frame (#1A or #1B) and align mounting plates (#7) to

mounting plates (#8) on rotor frame (#2).
a. If using a hoist, use a minimum of three lifting

straps to secure frame at locations shown in

Figure 1-1.

b. If using a power machine and loader equipped

with a quick attach hitch plate to lift hitch

frame (#1A), refer to

“Hook-up to Quick Attach

Hitch”

on page 16 for proper hook-up.

c. If using a power machine and loader equipped

with a Euro hitch plate to lift hitch frame (#1B),

refer to

“Hook-up to Euro Hitch”

on page 17 for

proper hookup.

d. If using a forklift, slide forks below the underside

of hitch frame (#1A or #1B) and bottom frame

spacer (#9). Secure frame to forks before moving

forklift.

4. Attach rotor frame (#2) to hitch frame (#1A or #1B) by

inserting 1/2" x 1 3/4" GR5 bolts (#3) through frame

mounting plates (#7 & #8) on hitch and rotor frames.

5. Place flat washers (#6) and lock washers (#5) on all

twelve 1/2" x 1 3/4" GR5 bolts (#3), then secure with

1/2" hex nuts (#4). Tighten 1/2" hex nuts (#4) to the

correct torque by referring to

“Section 8: Torque

Values Chart”

on page 28.

6. Once all twelve 1/2" GR5 bolts (#3) have been

tightened to the correct torque, ensure there are no

visible gaps between frame mounting

plates (#7 & #8).

Quick Attach Hitch & Euro Hitch Assembly

Figure 1-1

72164

Place lifting strap #1 here

Place lifting strap #2 here

Place lifting strap #3 here

Содержание AP-SD96





































Результаты поиска

Содержание AP-SD96

Отзывы:

Похожие инструкции для AP-SD96

Бренды по названию

Популярные бренды

Kubota AP-SD96, Руководство оператора

Результаты поиска

Содержание AP-SD96

Отзывы:

Похожие инструкции для AP-SD96

Бренды по названию

Популярные бренды