background image

Section 1: Assembly & Set-up 

Table of Contents

AP-SC7072 Skid Cutter 326-974MK

2/6/19

11

Case Drain Assembly

Figure 1-6

70406

Case Drain Assembly (Optional)

Refer to Figure 1-6:

1.

Ensure the Cutter is parked on a flat level surface, 
and if the cutter is attached to a skid steer, follow 
proper shut down procedures. See 

“Skid Steer 

Shutdown Procedures” 

on page 16.

2. Loosen six 3/8"-16 hex nuts (#2). Removing the hex 

nuts is not necessary.

3. Remove the motor shroud (#1) by pushing it toward 

the front of the unit then lifting it upward.

4. Remove plug from port (C) in hydraulic motor (#4).

5. Attach adapter fitting (#3) to port (C) in hydraulic 

motor (#4) as shown and tighten to correct torque.

6. Route hydraulic hose (#5) through designated areas 

(A & B) as shown.

7.

Attach female end of hydraulic hose (#5) to adapter 
fitting (#3) and tighten.

8. Place the motor shroud back in its designated place 

and pull back to lock it in place. Tighten hex nuts (#2) 
to correct torque.

9. Attach flat faced coupler (#6) to the male end of 

hydraulic hose (#5) and tighten.

10. Connect coupler (#6) to case drain reservoir on skid 

steer.

11. Zip tie the case drain hydraulic hose to the two 

existing hoses.Pressure Gauge Assembly (Optional)

WARNING

!

To avoid serious injury or death:  
Cutter deck can be slippery when wet. Always step on grip 

pads when possible. Never hurry. Make sure you have secure 

footing and hand hold when walking on the deck.

Содержание AP-SC7072





































Отзывы: