Kubota 329-181A Скачать руководство пользователя страница 6

Страница: 6 / 16

Assembly Instructions

PS20 Seed Cup Speed Increaser Kit 329-181A Assembly Instructions Manual No. 329-242MK

5/21/21

Assemble and Route Roller Chains

This kit requires the installation of three standard #40

roller chains. Refer to Figure 1-21 on page 14 to identify

each chain by pitch count and part number.
For detailed instructions on how to connect the ends of a

roller chain, refer to

“Connect/Disconnect Chain Links”

on page 7.

Installing 35 Pitch Count Roller Chain

Refer to Figure 1-10:

1. Disassemble roller chain (#47) at its connecting link.
2. Place roller chain (#47) on top of sprocket (#8A) of

the lower drive sub-assembly, then route roller chain

to the inside of both sprockets (#7).

3. Continue routing roller chain (#47) around the

underside of sprocket (#2) on the seeder’s rear roller

axle (X). Reconnect chain ends with connecting link.

Refer to

“Connect/Disconnect Chain Links”

page 7.

Installing and Routing Roller Chain (#47)

Figure 1-10

Installing 45 Pitch Count Roller Chain

Refer to Figure 1-11:

1. Disassemble roller chain (#1) at its connecting link.
2. Place roller chain (#1) on top of Primary Seeder’s

33 tooth sprocket (W).

3. Route roller chain (#1) to the underside of

sprocket (#7A) on the upper drive sub-assembly.

4. Continue routing roller chain (#1) to wrap around

sprocket (#6) installed on hex shaft (#14).

5. Continue routing roller chain (#1) to wrap under

sprocket (#6), and over top of sprocket (#7B).

6. Continue routing roller chain (#1) along underside

and around the 33 tooth sprocket (W). Reconnect

chain ends with connecting link. Refer to

“Connect/Disconnect Chain Links”

on page 7.

76271

Lower drive

sub-assembly

Installing and Routing Roller Chain (#1)

Figure 1-11

Installing 92 Pitch Count Roller Chain

Refer to Figure 1-12:

1. Hold the 60 tooth sprocket (#49) vertically in hand,

then hang roller chain (#48) over the sprocket.

2. With the 60 tooth sprocket (#49) in hand, hook roller

chain (#48) to the underside of sprocket (#8B).

3. Route the roller chain (#48) to the inside of idler

sprocket (#7) as shown in Figure 1-12.

4. Install the 60 tooth sprocket (#49) onto hex

shaft (#14), then secure sprocket to the hex shaft with

linchpin (#45).

Installing and Routing Roller Chain (#48)

Figure 1-12

76294

Upper drive

sub-assembly

NOTE:

The 92 pitch roller chain does not need to be

disassembled to be installed onto this kit.

NOTE:

If needed, temporarily unhook spring from

idler arm (#16) to ease installation of sprocket (#49)

onto hex shaft (#14).

Upper drive

sub-assembly

76272

Lower drive

sub-assembly

Содержание 329-181A

















Результаты поиска

Содержание 329-181A

Отзывы:

Похожие инструкции для 329-181A

Бренды по названию

Популярные бренды

Kubota 329-181A, Руководство по сборке

Результаты поиска

Содержание 329-181A

Отзывы:

Похожие инструкции для 329-181A

Бренды по названию

Популярные бренды