Kubota 329-181A Скачать руководство пользователя страница 7

Страница: 7 / 16

Assembly Instructions

5/21/21

PS20 Seed Cup Speed Increaser Kit 329-181A Assembly Instructions Manual No. 329-242MK

Connect/Disconnect Chain Links

Follow the procedure below when connecting chain link

ends after routing a roller chain.

Refer to Figure 1-13 & Figure 1-14:

1. Install connecting link to connect the chain ends.

Connect & Disconnect Roller Chains

Figure 1-13

2. Place connecting link plate onto pins of the

connecting link.

3. Using a pair of pliers, secure spring clip onto pins of

the connecting link.
a. Place spring clip over the first pin of the

connecting link. See correct method in

Figure 1-14.

b. Squeeze pliers against first pin for leverage and

backside of spring clip to force spring clip onto

both pins of the connecting link.

Securing Spring Clip

Figure 1-14

Connecting link

Spring clip

Connecting link plate

76298

NOTE:

Spring clip will be difficult to install if not first

placed over the connecting link’s first pin.

NOTE:

To disconnect the chain ends, squeeze pliers

against the second pin for leverage and the open end

of the spring clip to remove spring clip from pins.

Spring

clip

76299

Second

First

Wrong method

Correct method

Installing Snap-on Actuator

The snap-on actuator is magnetic and works in

conjunction with the acremeter pickup sensor to

communicate an accurate drive rotation count to the

acremeter. Follow the procedure below to ensure the

actuator gets installed correctly.

Refer to Figure 1-15 & Figure 1-16:

1. Disassemble actuator (#23) into two halves, then

reassemble onto hex shaft (#14).

Installing Actuator

Figure 1-15

2. Position actuator (#23) to be centered, and

approximately 1/8 inch (3mm) below to the acremeter

pickup sensor housing (Y).

Positioning Actuator

Figure 1-16

IMPORTANT:

Use caution when sliding the two

actuator halves back together to avoid breaking one

of the tabs.

76304

NOTE:

If needed, the location of the acremeter

pickup sensor can be adjusted on the machine.

IMPORTANT:

Ensure the pickup sensor housing end

opposite of its corresponding wire harness is the end

facing the actuator.

76322

Pickup sensor

wire harness

Acremeter

Содержание 329-181A

















Результаты поиска

Содержание 329-181A

Отзывы:

Похожие инструкции для 329-181A

Бренды по названию

Популярные бренды

Kubota 329-181A, Руководство по сборке

Результаты поиска

Содержание 329-181A

Отзывы:

Похожие инструкции для 329-181A

Бренды по названию

Популярные бренды