Kubota 329-181A Скачать руководство пользователя страница 4

Страница: 4 / 16

Assembly Instructions

PS20 Seed Cup Speed Increaser Kit 329-181A Assembly Instructions Manual No. 329-242MK

5/21/21

6. Eliminate gaps between chain guard mounts

(#11 & #12) and seeder frame by slightly loosening

hand knobs (B) securing both mounts.

Setting Position for New Chain Guard Mounts

Figure 1-5

Prepare to weld chain guard mounts (#11 & #12) to

the seeder’s steel frame.

8. Start by tacking each chain guard mount (#11 & #12)

in multiple places to the seeder’s steel frame.

9. Carefully remove chain guard (#10) from the seeder

by unthreading all three hand knobs (B). Remove

both lower hand knobs first.

10. Verify angle measurements of tacked chain guard

mounts (#11 & #12) are within one degree of their

specified angles shown in Figure 1-4 on page 3.

11. With the chain guard removed, add additional tacks

to chain guard mounts (#11 & #12).

12. Verify chain guard (#10) can still be secured to the

seeder with all three hand knobs (B), then carefully

remove the chain guard once more.

13. Weld both sides of chain guard mounts (#11 & #12) to

the seeder frame.

14. Use a chisel or putty knife to remove any excess weld

spatter from the seeder frame.

IMPORTANT:

Before welding, retighten each hand

knob while holding chain guard mount in place.

76280

IMPORTANT:

To avoid having to rework bad welds,

use a clean welding nozzle, and ensure the welding

machine is functioning properly by doing a test run on

scrap metal.

IMPORTANT:

Be sure to not exceed the specified

fillet weld size for each chain guard mount shown

Figure 1-4 on page 3.

15. After welding chain guard mounts (#11 & #12) to the

seeder frame, verify chain guard (#10) can still be

secured with all three hand knobs (B).

16. Remove chain guard (#10) and allow the welded

components to cool.

17. Wipe down and clean seeder where the new chain

guard mounts (#11 & #12) were welded.

18. Add touch-up paint to the newly installed

components and seeder frame. If touch-up paint

needs to be purchased, refer to the table below for

ordering information.

Installing Rear Roller Axle Sprocket

Refer to Figure 1-6:

1. Install sprocket (#2) onto rear roller axle (X), then

align sprocket bolt hole with bolt hole on rear roller

axle.

2. Secure sprocket (#2) to rear roller axle (X) with

1/4-20x2 3/4 GR8 bolt (#32) and flange hex

nut (#39). Tighten hardware to 12 ft-lbs (16 N

m).

3. Secure flange hex nut (#39) with hex nut (#33).

Tighten hex nut (#33) to 12 ft-lbs (16 N

m).

Installing Sprocket onto Rear Roller Axle

Figure 1-6

Touch-Up Paint

Part No.

Part Description

821-070C

Gloss black enamel spray can

821-070CTU Gloss black enamel bottle with brush
821-070CQT Gloss black enamel quart
821-070CGL Gloss black enamel gallon

76283

Содержание 329-181A

















Результаты поиска

Содержание 329-181A

Отзывы:

Похожие инструкции для 329-181A

Бренды по названию

Популярные бренды

Kubota 329-181A, Руководство по сборке

Результаты поиска

Содержание 329-181A

Отзывы:

Похожие инструкции для 329-181A

Бренды по названию

Популярные бренды