KTM Freeride 350 AU страница 56 Скачать руководство пользователя | Manualshive

Страница: 56 / 116

background image

12

SERVICE WORK ON THE CHASSIS

54

M00513-10

Main work

–

Pull the chain at the end of the chain sliding component upwards to measure chain
tension



.

Info

The lower chain section



must be taut.

Chain wear is not always even, so you should repeat this measurement at
different chain positions.

Chain tension

36… 40 mm (1.42… 1.57 in)

» If the chain tension does not meet specifications:

–

Adjust the chain tension. (

Finishing work

–

Remove the motorcycle from the lift stand. (

12.35

Adjusting the chain tension

Warning

Danger of accidents

Danger caused by incorrect chain tension.

–

If the chain is too taut, the components of the secondary power transmission (chain, engine sprocket, rear sprocket, bear-
ings in the transmission and in the rear wheel) will be under additional load. In addition to premature wear, this can cause
the chain or the countershaft of the transmission to break in extreme cases. If the chain is too loose, however, it may fall
off the engine sprocket or rear sprocket and block the rear wheel or damage the engine. Ensure that the chain tension is
correct and adjust it if necessary.

Preparatory work

–

Raise the motorcycle with the lift stand. (

–

Check the chain tension. (

M00514-10

Main work

–

Loosen nut



.

–

Loosen nuts



.

–

Adjust the chain tension by turning adjusting screws



on the left and right.

Guideline

Chain tension

36… 40 mm (1.42… 1.57 in)

Turn adjusting screws



on the left and right so that the markings on the

left and right chain adjusters are in the same position relative to reference
marks



. The rear wheel is then correctly aligned.

–

Tighten nuts



.

–

Make sure that chain adjusters



are fitted correctly on adjusting screws



.

–

Tighten nut



.

Guideline

Nut, rear wheel spindle

M20x1.5

80 Nm (59 lbf ft)

Info

The wide adjustment range of the chain adjusters enables different sec-
ondary ratios with the same chain length.
Chain adjusters



can be turned by 180°.

Finishing work

–

Remove the motorcycle from the lift stand. (

«
...
54
55
56
57
58
...
»

Содержание Freeride 350 AU





















































































































Отзывы:

Нет отзывов

Похожие инструкции для Freeride 350 AU

Бренд: Yamaha Страницы: 568

Бренд: Cobra Страницы: 2

Бренд: Happy Trails Страницы: 3

Бренд: Honda Страницы: 100

Бренд: Victory Motorcycles Страницы: 332

Бренд: KTM Power Parts Страницы: 22

Бренд: DYNATEK Страницы: 8

Бренд: DYNATEK Страницы: 12

Бренд: Dynafit Страницы: 21

Бренд: R&G Страницы: 6

Бренд: R&G Страницы: 6

Бренд: R&G Страницы: 9

Бренд: R&G Страницы: 6

Бренд: R&G Страницы: 6

Бренд: R&G Страницы: 9

Бренд: R&G Страницы: 17

Бренд: R&G Страницы: 25

Бренд: R&G Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды