background image

12

SERVICE WORK ON THE CHASSIS

53

12.32

Checking for chain dirt accumulation

400678-01

Check the chain for coarse dirt accumulation.
» If the chain is very dirty:

Clean the chain. (

p. 53)

12.33

Cleaning the chain

Warning

Danger of accidents

Oil or grease on the tires reduces their grip.

Remove oil and grease with a suitable cleaning material.

Warning

Danger of accidents

Reduced braking efficiency due to oil or grease on the brake discs.

Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Info

The service life of the chain depends largely on its maintenance.

Preparatory work

Raise the motorcycle with the lift stand. (

p. 37)

400725-01

Main work

Clean the chain regularly and then treat with chain spray.

Chain cleaner (

p. 106)

Off-road chain spray (

p. 106)

Finishing work

Remove the motorcycle from the lift stand. (

p. 37)

12.34

Checking the chain tension

Warning

Danger of accidents

Danger caused by incorrect chain tension.

If the chain is too taut, the components of the secondary power transmission (chain, engine sprocket, rear sprocket, bear-
ings in the transmission and in the rear wheel) will be under additional load. In addition to premature wear, this can cause
the chain or the countershaft of the transmission to break in extreme cases. If the chain is too loose, however, it may fall
off the engine sprocket or rear sprocket and block the rear wheel or damage the engine. Ensure that the chain tension is
correct and adjust it if necessary.

Preparatory work

Raise the motorcycle with the lift stand. (

p. 37)

Содержание Freeride 350 AU





















































































































Отзывы: