KTM F9903RE Скачать руководство пользователя

Страница: 15 / 22

WORK 3

H01291-10

–

Switch off the engine.

–

Open the filler cap. (

p. 13)

–

Fill the fuel tank with fuel up to the lower edge

of the filler

neck.

Total fuel tank
capacity, approx.

23 l
(6.1 US gal)

Super unleaded
(ROZ 95/RON
95/PON 91)
(

p. 19)

–

Close the filler cap. (

p. 14)

3.10

Opening the filler cap

Danger

Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.

–

Do not refuel the vehicle in the vicinity of open flames or lit cigarettes.

–

Switch off the engine for refueling.

–

Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

–

If any fuel is spilled, wipe it off immediately.

–

Observe the specifications for refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

–

Avoid skin, eye and clothing contact with fuel.

–

Immediately consult a doctor if you swallow fuel.

–

Do not inhale fuel vapors.

–

In case of skin contact, rinse the affected area with plenty of water.

–

Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

–

Change your clothing in case of fuel spills on them.

–

Keep fuels correctly in a suitable canister, and out of the reach of children.

Warning

Environmental hazard

Improper handling of fuel is a danger to the environment.

–

Do not allow fuel to enter the groundwater, the soil, or the sewage system.

H01281-10

–

Lift cover

of the filler cap and insert ignition key

in the

fuel tank lock.

Содержание F9903RE























Результаты поиска

Содержание F9903RE

Отзывы:

Похожие инструкции для F9903RE

Бренды по названию

Популярные бренды

KTM F9903RE, Инструкции по установке

Результаты поиска

Содержание F9903RE

Отзывы:

Похожие инструкции для F9903RE

Бренды по названию

Популярные бренды