background image

ENGLISH

8

Cooling liquid temperature display 

The temperature display 

1

is shown in 7 bars. The more bars that light up,

the hotter the cooling liquid. When the lowest bar lights up, the cooling
liquid has reached a temperature of approx. 40°C (104°F). When the upper
bar lights up 120°C (248°F), all of the bars will start to blink and the red
warning lamp 

2

will light up.

WARNING

P

OSSIBLE CAUSES FOR AN INCREASE IN TEMPERATURE

CAUSING THE RED WARNING LIGHT

FOR THE COOLING LIQUID TEMPERATURE TO LIGHT UP

:

– D

RIVING TOO SLOWLY AND DRIVING WITH A HEAVY LOAD AT HIGH AIR TEMPERATURES

– N

OT ENOUGH COOLING LIQUID IN THE SYSTEM

– T

HE VENTILATOR ON THE RADIATOR IS NOT RUNNING

– I

MPROPER USE OF THE CLUTCH WHEN DRIVING SLOWLY

Indicator lamps

The green indicator lamp will blink in the blinker rhythm when the
blinker is switched on.
NOTE:
The indicator lamp will blink slower when a blinker is broken.

The green indicator lamp will light up when the gearbox is in an
idling position.

The blue indicator lamp will light up when the high beams are
switched on.

The red warning light will light up when the cooling liquid has
reached a temperature of approx. 120°C (248°F).

The orange warning light will start to blink when the fuel level has
reached the reserve mark. At the same time the display will auto-
matically change to TRIP F (see TRIP F).

The red warning lamp lights up when the ignition is switched on
but the engine is not running. When the engine is started, the war-
ning lamp will go out as soon as the oil pressure is high enough.

This indicator lamp has no function.

Tachometer

The tachometer shows the engine speed in revolutions per minute. Do not
run the engine beyond the black mark at 9500 rpm.
The speed limiter will set in at 9600 rpm, drastically reducing the engine
power above this rotational speed.

120°C  (248°F)

110°C  (230°F)

100°C  (212°F)

70°C  (158°F)

60°C  (140°F)

50°C  (122°F)

40°C  (104°F)

1

2

Содержание 950 ADVENTURE 2004


























































Отзывы: