KTM 85 SX 2004 Скачать руководство пользователя

Страница: 71 / 89

7-2

Repair manual KTM 85 SX

Art No 3.206.008-E

Resistor values of the ignition system - Stator

– Unplug the connector on the ignition stator and measure the

resistance of the stator coils at 20° C using a digital multimeter.

Pulse generator:

between the white/red and white/blue cable

Multimeter display: 310

Ω

+/- 60

Ω

CDI voltage supply:

between the green/blue and black cable

Multimeter display: 55

Ω

+/- 10

Ω

Capacitor charging coil:

between the black/red and green/white cable

Multimeter display: 900

Ω

+/- 180

Ω

NOTE: the stator does not need to be removed to measure.

Ignition coil

– Unscrew the spark plug connector and disconnect the cable for the

primary drive.

– Measure the resistance on the primary side of the ignition coil

between the primary drive plug and the ignition coil ground.

Multimeter display: under 10

Ω

at 20º C

– Measure the resistance on the secondary side of the ignition coil

between the high voltage cable and the ignition coil ground.

Multimeter display: 7900

Ω

+/- 1500

Ω

at 20º C

NOTE: The ignition coils do not need to be removed to measure.

Содержание 85 SX 2004


























































































Результаты поиска

Содержание 85 SX 2004

Отзывы:

Похожие инструкции для 85 SX 2004

Бренды по названию

Популярные бренды

KTM 85 SX 2004, Руководство по ремонту

Результаты поиска

Содержание 85 SX 2004

Отзывы:

Похожие инструкции для 85 SX 2004

Бренды по названию

Популярные бренды