KTM 2009 690 Rally Factory Replica Скачать руководство пользователя

Страница: 49 / 104

MAINTENANCE WORK ON CHASSIS AND ENGINE

8.44

Checking free play of foot brake lever

Warning

Danger of accidents

Brake system failure.

–

If there is no free travel on the foot brake pedal, pressure builds up on the rear brake in the brake system. The rear brake
can fail due to overheating. Adjust free travel on foot brake pedal according to specifications.

400291-11

–

Move the foot brake lever backwards and forwards between the end stop and the
foot brake cylinder piston bracket and check free play



Guideline

Free play at foot brake lever

3… 5 mm (0.12… 0.2 in)

» If the free travel does not meet specifications:

–

Adjust the free travel of the foot brake pedal.

(

p. 47)

8.45

Adjusting free travel of foot brake pedal

Warning

Danger of accidents

Brake system failure.

–

400291-13

–

Loosen the nut



and use the screw



to adjust the free travel



Guideline

Free play at foot brake lever

3… 5 mm (0.12… 0.2 in)

–

Hold screw



and tighten nut



Guideline

Remaining nuts, chassis

10 Nm (7.4 lbf ft)

8.46

Checking rear brake fluid level

Warning

Danger of accidents

Brake system failure.

–

If the brake fluid level falls below the

MIN

mark, this indicates a leakage in the brake system or worn-out brake linings.

Have the brake system checked in an authorized KTM workshop, and do not ride any further.

Warning

Danger of accidents

Reduced braking due to old brake fluid.

–

Have the front and rear brake fluid replaced according to the service plan in an authorized KTM workshop.

600060-10

–

Stand the vehicle upright.

–

Check the brake fluid level in the brake fluid reservoir



» When the fluid level reaches the

MIN

mark



–

Add rear brake fluid.

(

p. 48)

Содержание 2009 690 Rally Factory Replica









































































































Результаты поиска

Содержание 2009 690 Rally Factory Replica

Отзывы:

Похожие инструкции для 2009 690 Rally Factory Replica

Бренды по названию

Популярные бренды

KTM 2009 690 Rally Factory Replica, Руководство пользователя

Результаты поиска

Содержание 2009 690 Rally Factory Replica

Отзывы:

Похожие инструкции для 2009 690 Rally Factory Replica

Бренды по названию

Популярные бренды