KTM 1190 RC8 R Track страница 64 Скачать руководство пользователя | Manualshive

Страница: 64 / 127

background image

SERVICE WORK ON THE CHASSIS

62

Info

The service life of the chain depends largely on its maintenance.

400725-01

–

Clean the chain regularly.

–

Rinse off loose dirt with a soft jet of water.

–

Remove old grease remains with chain cleaner.

Chain cleaner (

–

After drying, apply chain spray.

Chain lube for road use (

10.23

Checking the chain tension

Warning

Danger of accidents

Danger caused by incorrect chain tension.

–

If the chain tension is too high, the components of the secondary power train (chain, engine sprocket, rear sprocket, bear-
ings in transmission and rear wheel) are under additional load. Apart from premature wear, in extreme cases the chain can
rupture or the countershaft of the transmission can break. On the other hand, if the chain is loose, it can fall off the engine
sprocket or the rear sprocket and block the rear wheel or damage the engine. Check the chain tension and correct if neces-
sary.

–

Raise the rear of the motorcycle with lifting gear. (

700322-01

–

Shift into neutral.

–

In the area in front of where the chain passes through the link fork, push the chain
upward and measure chain tension



.

Info

The lower chain section



must be taut.

Chain wear is not always even, so you should repeat this measurement at
different chain positions.

Chain tension

15… 20 mm (0.59… 0.79 in)

» If the chain tension does not meet specifications:

–

Adjust the chain tension. (

10.24

Adjusting the chain tension

Warning

Danger of accidents

Danger caused by incorrect chain tension.

–

If the chain tension is too high, the components of the secondary power train (chain, engine sprocket, rear sprocket, bear-
ings in transmission and rear wheel) are under additional load. Apart from premature wear, in extreme cases the chain can
rupture or the countershaft of the transmission can break. On the other hand, if the chain is loose, it can fall off the engine
sprocket or the rear sprocket and block the rear wheel or damage the engine. Check the chain tension and correct if neces-
sary.

–

Check the chain tension. (

–

Remove the rear frame sliders. (

«
...
62
63
64
65
66
...
»

Содержание 1190 RC8 R Track
































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1190 RC8 R Track

Бренд: Crivit Страницы: 70

Бренд: Suzuki Страницы: 151

EC-SIX DAYS - PART LIST 2011

Бренд: GAS GAS Страницы: 6

Бренд: VEB Страницы: 63

Бренд: Termignoni Страницы: 9

Бренд: SHERCO Страницы: 76

Бренд: X-lite Страницы: 33

Бренд: Honda Страницы: 98

Virago XV1100K(C)

Бренд: Yamaha Страницы: 111

Бренд: Yamaha Страницы: 101

Бренд: DYNATEK Страницы: 1

Бренд: Twiins Страницы: 40

ZIEGER 10005243

Бренд: IBEX Страницы: 4

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 278

Бренд: TVS Страницы: 44

Бренд: Tusk Страницы: 3

CYBERCHARGER 50002

Бренд: Ciro Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды