KSB Vitastage Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 44

background image

7 Servicing/Maintenance

33 of 44

Vitastage

For dismantling and reassembly observe the exploded views and the general
assembly drawing.

NOTE

All maintenance work, service work and installation work can be carried out by KSB
Service or authorised workshops. For contact details please refer to the enclosed
"Addresses" booklet or visit "

www.ksb.com/contact

" on the Internet.

DANGER

Insufficient preparation of work on the pump (set)

Risk of injury!

▷

Properly shut down the pump set.

Section 6.1.5, Page 25)

▷

Close the shut-off elements in the suction line and discharge line.

▷

Drain the pump and release the pump pressure.

▷

Shut off any auxiliary feed lines.

▷

Allow the pump set to cool down to ambient temperature.

NOTE

After a prolonged period of operation the individual components may be hard to
pull off the shaft. If this is the case, use an appropriate pull-off device, if possible.

7.4.2 Preparing the pump set

DANGER

Power supply not disconnected

Danger to life!

▷

Disconnect all electrical connections from the power supply and secure against
unintentional start-up.

1.

De-energise the pump set and secure it against unintentional start-up.

7.4.3 Removing the complete pump set from the piping

1.

Disconnect the discharge nozzle and suction nozzle from the piping.

2.

Depending on the pump size and motor size, unscrew the bolts that fix the
support foot or motor foot to the foundation.

3.

Remove the complete pump set from the piping.
Alternative: Leave pump casing 101 installed in the piping. Undo clamping piece
81-44. Pull the remaining back pull-out unit out towards the back (back pull-out
design).

7.4.4 Dismantling the pump

The dismantling procedure is the same for all sizes. It only differs in the number of
stages to be dismantled.

See general assembly drawing with list of components

Section 9.1, Page 38)

and

Section 9.2, Page 39)

1.

Undo cap nuts (38) and remove them together with washers (37).

2.

Remove suction cover (7) (for vertically installed pumps: remove foot with
suction cover (7)). Undo and remove grub screws (36).

3.

Remove O-ring (16) and joint ring (30) (suction cover).

4.

Undo and remove impeller nut (14).

5.

Pull first impeller (5) off shaft (50).

«
...
31
32
33
34
35
...
»

Содержание Vitastage













































Отзывы:

Нет отзывов

Похожие инструкции для Vitastage

Бренд: Waterous Страницы: 10

Бренд: SGS Страницы: 10

Smartmax Series

Бренд: ubbink Страницы: 29

Бренд: REHOBOT Страницы: 14

Tranquility TR Series

Бренд: ClimateMaster Страницы: 96

Бренд: Lampoassa Страницы: 62

Бренд: ABS Страницы: 10

Бренд: NAVAC Страницы: 8

RESIDENTIAL GAS FIRED WATER HEATERS

Бренд: Giant Страницы: 8

Бренд: Ingersoll-Rand Страницы: 1

Бренд: Peraqua Страницы: 60

ProSeries Chem-Feed CFPS-1

Бренд: Blue-White industries Страницы: 12

Boiler Square B 23

Бренд: Quick Страницы: 36

AFFINITY YZB02411

Бренд: York Страницы: 38

Бренд: P.I.T. Страницы: 18

Бренд: Graco Страницы: 28

Бренд: Becker Страницы: 6

BTN 120 THRU 400/A Series

Бренд: A.O. Smith Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды