KSB Vitastage Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 44

background image

5 Installation at Site

22 of 44

Vitastage

5.6.3 Earthing

DANGER

Electrostatic charging

Explosion hazard!

Fire hazard!

Damage to the pump set!

▷

Connect the PE conductor to the earthing terminal provided.

5.7 Checking the direction of rotation

DANGER

Temperature increase resulting from contact between rotating and stationary
components

Damage to the pump set!

▷

Never check the direction of rotation by starting up the unfilled pump set.

▷

Separate the pump from the motor to check the direction of rotation.

WARNING

Hands inside the pump casing

Risk of injuries, damage to the pump!

▷

Always disconnect the pump set from the power supply and secure it against
unintentional start-up before inserting your hands or other objects into the
pump.

CAUTION

Incorrect direction of rotation with non-reversible mechanical seal

Damage to the mechanical seal and leakage!

▷

Separate the pump from the motor to check the direction of rotation.

CAUTION

Drive and pump running in the wrong direction of rotation

Damage to the pump!

▷

Refer to the arrow indicating the direction of rotation on the pump.

▷

Check the direction of rotation. If required, check the electrical connection and
correct the direction of rotation.

The correct direction of rotation of the motor and pump is clockwise (seen from the
motor end).

1.

Start the motor and stop it again immediately to determine the motor's
direction of rotation.

2.

Check the direction of rotation.
The motor's direction of rotation must match the arrow indicating the direction
of rotation on the pump.

3.

If the motor runs in the wrong direction of rotation, check the electrical
connection of the motor and the control system, if applicable.

«
...
20
21
22
23
24
...
»

Содержание Vitastage













































Отзывы:

Нет отзывов

Похожие инструкции для Vitastage

BURKAY 102 Series

Бренд: A.O. Smith Страницы: 24

Бренд: ubbink Страницы: 29

Бренд: YANGTECH Страницы: 23

Бренд: WAGNER Страницы: 100

DURA-Power DRE-52

Бренд: A.O. Smith Страницы: 26

DURA-Power DRE-52

Бренд: A.O. Smith Страницы: 20

Instant-Flow Micro M-15L/277

Бренд: Chronomite Страницы: 2

Бренд: K Tool International Страницы: 20

Comfort 5000/5 LCD

Бренд: Gardena Страницы: 13

Бренд: GEA Страницы: 66

Бренд: salmson Страницы: 48

Бренд: Wacker Neuson Страницы: 50

Pneumatic Oilpump 3:1

Бренд: Pressol Страницы: 28

Бренд: Helios Страницы: 44

Бренд: Immergas Страницы: 16

Бренд: Trane Страницы: 44

Бренд: TapFlo Страницы: 45

Бренд: TapFlo Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды