KSB Magnochem-Bloc Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 96

background image

7 Servicing/Maintenance

66 of 96

Magnochem-Bloc

4. Carefully slide containment shroud flange 723 over containment shroud 82-15

and place it onto casing cover 161.

5. Tighten hexagon socket head cap screws 914.03 crosswise. Observe the

tightening torques. Apply half of the permissible tightening torque to each
screw during the first round of tightening. Then apply the tightening torque
specified. (

Section 7.6, Page 74)

Design with intermediate piece

ü

The notes and steps stated in (

Section 7.5.1, Page 59) to

Section 7.5.3, Page 64) have been observed and carried out.

ü

The individual parts have been placed in a clean and level assembly area.

ü

All dismantled parts have been cleaned and checked for wear.

ü

Any damaged or worn parts have been replaced by original spare parts.

ü

The sealing surfaces have been cleaned.

ü

The inner rotor assembly has been placed on the impeller in a vertical position
and secured against tilting.

CAUTION

Improper tightening of the bolts on the containment shroud

Damage to the containment shroud!

▷

Evenly tighten the bolts crosswise.

1. Check the inner rotor for contamination (e.g. metal particles) and clean if

necessary.

2. Insert joint ring 411.08 into casing cover 161.

3. Place intermediate piece 132.01 onto casing cover 161.

4. Tighten hexagon socket head cap screws 914.03 to the torques given in this

manual. (

Section 7.6, Page 74)

5. Insert joint ring 411.09 into intermediate piece 132.01.

6. Place containment shroud 82-15 onto intermediate piece 132.01.

7. Tighten hexagon socket head cap screws 914.03 crosswise. Observe the

tightening torques. Apply half of the permissible tightening torque to each
screw during the first round of tightening. Then apply the tightening torque
specified. (

Section 7.6, Page 74)

7.5.5 Fitting the bearing bracket lantern

CAUTION

Collision between bearing bracket lantern and containment shroud

Damage to the containment shroud!

▷

Use a suitable guard to protect the containment shroud (see table for
manufacturing dimensions of guard).

«
...
64
65
66
67
68
...
»

Содержание Magnochem-Bloc

































































































Отзывы:

Нет отзывов

Похожие инструкции для Magnochem-Bloc

Бренд: Kanomax Страницы: 2

Бренд: Keithley Страницы: 156

Бренд: MADDALENA Страницы: 4

Бренд: Macnaught Страницы: 4

Portable Grand DGX-670

Бренд: Yamaha Страницы: 93

Portatone PSR-410

Бренд: Yamaha Страницы: 65

Бренд: Mini Страницы: 20

Бренд: Bamo Страницы: 17

BUCKMASTERS 1500

Бренд: Sig Sauer Страницы: 2

FG-3000R Series

Бренд: Nidec Страницы: 8

Бренд: Seben Страницы: 16

Бренд: PASCO Страницы: 4

DELMHORST J-2000

Бренд: ABQ Industrial Страницы: 4

Бренд: General Страницы: 12

Precision KMS7101

Бренд: Kreg Страницы: 16

Бренд: VOLTCRAFT Страницы: 8

LaserRange-Master i5

Бренд: LaserLine Страницы: 68

Бренд: GE Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды