KSB Magnochem-Bloc Скачать руководство пользователя страница 63

Страница: 63 / 96

7 Servicing/Maintenance

63 of 96

Magnochem-Bloc

CAUTION

Non-observance of the assembly sequence of disc springs 950.23 and intermediate
ring 509.02.

Damage to the plain bearings!

▷

Observe the assembly sequence.

▷

Pay due attention to the arrangement of the plain bearings.

Table 17:

Number of disc springs 950.23

Bearing bracket

Nominal diameter of magnetic coupling

123

172

CS40

CS50

CS60

14. Slide disc spring 950.23 (see table: Number of disc springs 950.23) onto shaft

210.03.

Bearing brackets CS50 and CS60 with nominal magnetic coupling diameters 85
and 123 only:

slide intermediate ring 509.02 and disc spring 950.23 (see table:

Number of disc springs) onto shaft 210.03.

15. Fit drive-end taper lock ring 515.22.

NOTE

Bearing sleeves 529.21 and 529.22 are identical.

16. Slide bearing sleeve 529.22 onto the shaft.

CAUTION

Dry bearing surfaces during assembly

Dry running of the bearings at pump start-up!

▷

Before installing the bearings, wet the running surfaces of the bearings with a
suitable fluid (e.g. water or oil).

17. Wet the bearing bush with liquid.

CAUTION

Incorrect assembly

Damage to the plain bearing assembly!

▷

Prevent tilting of casing cover 161 with bearing ring carrier 391 on shaft 210.03.

▷

Carefully and slowly slide casing cover 161 with bearing ring carrier 391 onto
shaft 210.03.

18. Slide the pre-assembled assembly of casing cover 161 and bearing ring carrier

391 onto shaft 210.03.

WARNING

Insufficient stability

Risk of crushing hands and feet!

▷

Secure the pre-assembled plain bearing assembly against tilting or tipping over
during reassembly.

19. Slide bearing sleeve 529.21 onto shaft 210.03.

Содержание Magnochem-Bloc

































































































Результаты поиска

Содержание Magnochem-Bloc

Отзывы:

Похожие инструкции для Magnochem-Bloc

Бренды по названию

Популярные бренды

KSB Magnochem-Bloc, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Magnochem-Bloc

Отзывы:

Похожие инструкции для Magnochem-Bloc

Бренды по названию

Популярные бренды