KSB Hya-Rain Скачать руководство пользователя страница 29

Страница: 29 / 64

6 Commissioning/Start-up/Shutdown

29 of 64

Hya-Rain/Hya-Rain N

6.1.3 Start-up

Hya-Rain

The power plug has been plugged into the socket.

1. Set the master switch to 1. (

Section 7, Page 32)

The pump control unit controls the system automatically:

▪

When a consumer installation is opened, the pump set starts up.

▪

When all consumer installations are closed, the pump set stops.

Table 7:

Description of indicator lamps

Lamp

Description

Green

Ready for operation

Red

Lack of water: Dry running protection stops the pump set.

Fault: A fault can be reset by pressing the reset key. When the reset key
is pressed and held down, the system is in manual mode.

Hya-Rain N

The power plug has been plugged into the socket.

1. Set the master switch to 1. (

Section 7, Page 32)

2. Calibrate the level display. (

Section 7.3.1, Page 36)

6.1.4 Functional test

Dry running protection

The system has been properly set up, installed, connected and commissioned.

1. Close the suction-side inlet of the rainwater storage tank.

No flow. The pump control unit stops the pump set after an after-run time of
approx. 10 seconds.

2. If necessary, repeat the after-run time by pressing the reset key.

Operating modes

The system has been properly set up, installed, connected and commissioned.

1. Check the indicator lamps:

Table 8:

Indicator lamps for operating modes

Operating mode

Symbol

Indicator lamp

Automatic mode

This indicator lamp lights up when the pump automatically switches to the
available water tank.

Mains water mode

This indicator lamp lights up when the pump withdraws water from the
mains water storage tank and the mains water back-up system is activated.

Rainwater storage tank

This indicator lamp lights up when the pump withdraws water from the
rainwater storage tank.

Содержание Hya-Rain

































































Результаты поиска

Содержание Hya-Rain

Отзывы:

Похожие инструкции для Hya-Rain

Бренды по названию

Популярные бренды

KSB Hya-Rain, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Hya-Rain

Отзывы:

Похожие инструкции для Hya-Rain

Бренды по названию

Популярные бренды