KSB Hya-Rain Скачать руководство пользователя страница 18

Страница: 18 / 64

5 Installation at Site

18 of 64

Hya-Rain/Hya-Rain N

5 Installation at Site

5.1 Safety regulations

DANGER

Unsuitable electrical installation

Danger to life!

▷

Make sure the electrical installation meets the VDE 0100 installation rules (i.e.
sockets with earthing terminals).

▷

Make sure the electric mains is equipped with a residual current device of
maximum 30 mA.

▷

Always have the electrical connections installed by a trained and qualified
electrician.

5.2 Checks to be carried out prior to installation

Before beginning with the installation check the following:

▪

The system can be operated on the power supply network according to the data
on the name plate. (

Section 4.3, Page 14)

▪

The fluid to be handled matches the description of suitable fluids.
(

Section 6.2.3.1, Page 30)

▪

The installation room is dry, frost-free and well-ventilated.

▪

The ambient conditions have been met. (

Section 6.2.1, Page 30)

▪

The wall (e.g. outside wall) is suitable for accommodating 4 plug fixings of
10 mm diameter and for carrying the weight of the system.
(

Section 4.8, Page 17)

5.3 Setting up and installing the system

A suitable installation site has been selected that meets the requirements.

Sufficient clearance in all directions is provided for servicing work.

1. Fasten the bolt hole pattern provided to the corresponding wall.

(

Section 10.4, Page 57)

2. Drill four holes of 10 mm diameter in accordance with the bolt hole pattern.

3. Insert the plug fixings.

4. Mount and align the lower hanging brackets.

5. Undo the nuts. Remove the cover.

6. Place the system on the lower hanging brackets.

7. Fit the upper hanging brackets.

8. Fit the system cover. Fasten it with nuts.

Содержание Hya-Rain

































































Результаты поиска

Содержание Hya-Rain

Отзывы:

Похожие инструкции для Hya-Rain

Бренды по названию

Популярные бренды

KSB Hya-Rain, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Hya-Rain

Отзывы:

Похожие инструкции для Hya-Rain

Бренды по названию

Популярные бренды