KSB Etaseco C Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 60

background image

7.4.5 Removing the casing cover/bearing bracket
Motor DS 90

✓

The notes and steps stated in (

Section 7.4.1 Page 39) to (

Section 7.4.4 Page

40) have been observed/carried out.

1. Pull off bush 540.01, cup springs 950.23 and thrust bearing 314.01.
2. Undo socket head cap screws 914.04 and pull off casing cover 161.
3. Remove O-rings 412.11, 412.41 and 412.71.

Motors DS 112 and 132

✓

The notes and steps stated in (

Section 7.4.1 Page 39) to (

Section 7.4.4 Page

40) have been observed/carried out.

1. Undo nuts 920.15 and take casing cover 161 off bearing bracket lantern 344.
2. Pull bush 540.01, cup springs 950.23 and thrust bearing 314.01 off the rotor.
3. Undo nuts 920.04 and remove bearing bracket lantern 344.
4. Remove O-rings 412.11/.41/.71.

7.4.6 Dismantling the rotor

✓

The notes and steps stated in (

Section 7.4.1 Page 39) to (

Section 7.4.5 Page

41) have been observed/carried out.

CAUTION

Incorrect dismantling

Damage to rotor and can!

▷

Keep the rotor straight to prevent any rubbing contact with the can when
pulling the rotor out.

1. Pull rotor 818 carefully out of the rotor space.

7.4.7 Dismantling the bearings

✓

The notes and steps stated in (

Section 7.4.1 Page 39) to (

Section 7.4.6 Page

41) have been observed/carried out.

1. Pull pump-end bearing sleeve 529.21 and thrust bearing 314.02 off the rotor.
2. Remove socket head cap screw 914.80 (left-hand thread!) as well as cup springs

950.11.

3. Pull rings 515.23, 515.24 and motor-end bearing sleeve 529.06 off the shaft end.
4. Remove socket head cap screws 914.72 and pull off bearing carrier 382.
5. Remove O-ring 412.02.

7.4.8 Cleaning and checking the components

✓

The notes and steps stated in (

Section 7.4.1 Page 39) to (

Section 7.4.7 Page

41) have been observed/carried out.

1. Clean all dismantled components and inspect them for signs of damage.
2. Replace any damaged components by original spare parts.
3. If the can is damaged:

- Replace the complete motor unit.
- For disposal open the stator space and completely dismantle the motor unit, if
required.

4. Inspect the bores located in the following components for cleanliness and free

passage. Clean them, if necessary.
- Impeller 230
- Thrust bearing 314.01/.02
- Bearing carrier 382
- Rotor 818 (radial bores; axial bore)

7 Servicing/Maintenance

Etaseco/Etaseco I

41 of 60

«
...
39
40
41
42
43
...
»

Содержание Etaseco C





























































Отзывы:

Нет отзывов

Похожие инструкции для Etaseco C

Бренд: Calpeda Страницы: 80

Бренд: Panasonic Страницы: 100

Aquarea WH-MDF09C3E5

Бренд: Panasonic Страницы: 90

Бренд: Panasonic Страницы: 80

Evosta2 11/139 SAN V

Бренд: DAB Страницы: 31

Бренд: DAB Страницы: 19

Бренд: Danfoss Страницы: 16

Бренд: Waterous Страницы: 13

Бренд: Waterous Страницы: 57

Бренд: GEA Страницы: 78

Бренд: Vaillant Страницы: 40

Бренд: Rowi Страницы: 40

Бренд: EINHELL Страницы: 44

Бренд: ICI Caldaie Страницы: 48

Бренд: A.O. Smith Страницы: 44

PROTÉGÉ RPAGP

Бренд: Raypak Страницы: 3

Бренд: Alpine Страницы: 20

Бренд: Daikin Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды