KSB Etaseco C Скачать руководство пользователя страница 11

Страница: 11 / 60

Transport/Temporary Storage/Disposal

CAUTION

Non-compliance with permissible cable bending radius

Damage to the cable!

▷

Observe the permissible minimum bending radius indicated in the
manufacturer's data sheet; consult KSB, if necessary.

3.1

Transport

DANGER

The pump (set) could slip out of the suspension arrangement.

Danger to life from falling parts!

▷

Transport the pump (set) as shown.

▷

Never attach the suspension arrangement to the free shaft end of the motor.

▷

Refer to the weights given in the general arrangement drawing.

▷

Observe the local accident prevention regulations.

▷

Use suitable, permitted lifting tackle, e.g. self-tightening lifting tongs.

To transport the pump/pump set suspend it from the lifting tackle as shown.

Fig. 1: Transporting the pump set

Fig. 2: Transporting the pump set (motor on top)

3 Transport/Temporary Storage/Disposal

Etaseco/Etaseco I

11 of 60

Содержание Etaseco C





























































Результаты поиска

Содержание Etaseco C

Отзывы:

Похожие инструкции для Etaseco C

Бренды по названию

Популярные бренды

KSB Etaseco C, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Etaseco C

Отзывы:

Похожие инструкции для Etaseco C

Бренды по названию

Популярные бренды