KSB Etanorm V Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 62

background image

1 General

6 of 62

Etanorm V

1228.87/01-EN

1 General

1.1 Principles

This operating manual is valid for the type series and variants indicated on the front
cover.

The operating manual describes the proper and safe use of this equipment in all
phases of operation.

The name plate indicates the type series and size, the main operating data, the order
number and the order item number. The order number and order item number
clearly identify the pump set and serve as identification for all further business
processes.

In the event of damage, immediately contact your nearest KSB service facility to
maintain the right to claim under warranty.

1.2 Installation of partly completed machinery

To install partly completed machinery supplied by KSB refer to the sub-sections under
Servicing/Maintenance.

1.3 Target group

This operating manual is aimed at the target group of trained and qualified specialist
technical personnel. (

Section 2.3, Page 8)

1.4 Other applicable documents

Table 1:

Overview of other applicable documents

Document

Contents

Data sheet

Description of the technical data of the pump (set)

General arrangement drawing /
outline drawing

Description of mating dimensions and installation
dimensions for the pump (set), weights

Drawing of auxiliary connections Description of auxiliary connections

Hydraulic characteristic curve

Characteristic curves showing head,
NPSH required, efficiency and power input

General assembly drawing

1)

Sectional drawing of the pump

Sub-supplier product literature

1)

Operating manuals and other product literature
describing accessories and integrated machinery
components

Spare parts lists

1)

Description of spare parts

Piping layout

1)

Description of auxiliary piping

List of components

1)

Description of all pump components

Assembly drawing

1)

Sectional drawing of the installed shaft seal

For accessories and/or integrated machinery components, observe the relevant
manufacturer's product literature.

1.5 Symbols

Table 2:

Symbols used in this manual

Symbol

Description

✓

Conditions which need to be fulfilled before proceeding with the
step-by-step instructions

⊳

Safety instructions

⇨

Result of an action

⇨

Cross-references

1

If included in agreed scope of supply

«
...
4
5
6
7
8
...
»

Содержание Etanorm V































































Отзывы:

Нет отзывов

Похожие инструкции для Etanorm V

Бренд: York International Страницы: 87

Бренд: T.I.P. Страницы: 66

Бренд: Tandem Страницы: 120

Бренд: Vaillant Страницы: 40

Бренд: Barracuda PUMPS Страницы: 4

Бренд: Flux Страницы: 80

Бренд: Serenity Страницы: 3

Бренд: Gardena Страницы: 17

Бренд: ABS Страницы: 10

Бренд: NAVAC Страницы: 8

Бренд: Pfeiffer Vacuum Страницы: 60

Бренд: Parkside Страницы: 122

JUNG PUMPEN SIMER 4

Бренд: Pentair Страницы: 10

Бренд: Samoa Страницы: 28

F Design Series

Бренд: Continental Hydraulics Страницы: 8

Бренд: Laars Страницы: 20

Cylinder DuroTech MAP07

Бренд: Milwaukee Страницы: 20

Бренд: Wacker Neuson Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды