Kruger KF50E, Руководство пользователя

Страница: 20 / 28

20
21 SQUEEGEE BUMPER WHEEL
22 SQUEEGEE BLADES REPLACEMENT KNOB
23 SQUEEGEE WHEEL
24 SQUEEGEE FIXING KNOB
25 SQUEEGEE INCLINATION ADJUSTMENT KNOB
26 SUCTION HOSE
5.3 ACCESSORIES
Your machine supplier can provide a complete and
updated list of all available accessories, such as brushes,
scrapers, disks, etc.
6. INSTALLATION INFORMATION
6.1 MACHINE PREPARATION
Before starting to work, wear non-slip shoes, gloves
and any other personal protection device indicated by
the supplier of the detergent used or considered
necessary based on the operating environment.
Do the following before starting to work. Refer to
the relative sections for a detailed description of these
steps:
Mount the brushes or scraper disks (with the abrasive
disks) that are suitable for the surface and work involved.
Mount the squeegee, check that it is solidly attached
and connected to the suction hose and that the drying
straps are not too worn. (PHOTO D)
Make sure that the recovery tank is empty. If not, empty
it completely. (PHOTO B-11)
Check and completely close the detergent solution
release control. (PHOTO B-10)
Fill the detergent solution tank with a mix of clean water
and non-foaming detergent in an adequate concentration
through the anterior hole (PHOTO A-3). Leave 2 cm
between the mouth of the plug and the level of the
liquid.
To avoid risks, become familiar with the machine
movements, carrying out test runs on a large surface
without obstacles.
To obtain the best results in terms of cleaning and
equipment service life, you should do the following
simple but important operations:
- Identify the work area, moving all possible obstacles
out of the way; if the surface is very extensive, work in
contiguous and parallel rectangular areas.
- Choose a straight work trajectory and begin working
from the farthest area to avoid passing over areas that
have already been cleaned.
7 OPERATING INFORMATION
7.1 SQUEEGEE AND SPLASH GUARD ASSEMBLY,
DISASSEMBLY AND ADJUSTMENT
The squeegee is the main component that ensures
perfect drying.
7.1.1 SQUEEGEE ASSEMBLY
Lower the lifting system to avoid having to keep the
body raIsed while completing connections. (PHOTO B-
16)
Screw the two knobs placed on the squegee (PHOTO
D-24) into the special hoses situated on the squeegee
support.
Firmly insert the suction hose into the hole in the
squeegee body (PHOTO D-26)
7.1.2 SQUEEGEE DISASSEMBLY
Lower the lifting system to avoid having to keep the body
raised while completing connections. (PHOTO B-16)
Unscrew the two knobs placed on the squegee (PHOTO
D-24) into the special hoses situated on the squeegee
support.
Disconnect the suction hose from the squeegee body.
(PHOTO D-26)
Now free the squeegee from its support (PHOTO D)
7.1.3 - 7.1.4 SQUEEGEE BLADES DISASSEMBLY /
ASSEMBLY
Unscrew the knobs placed on the squegee (PHOTO
D-22-24) and pull the plastic support of the squueegee
blades out from the squeegee body.
Tear off the rubber blades from the plastic support.
To assembly the squeegee blades, follow backwards
the same procedure.
7.1.5 SQUEEGEE ADJUSTMENT
The pivot screw on the body (PHOTO D-25) adjust the
squeegee’s slant with respect to the plane, according
to the machine’s longitudinal axis. The two handles on
the sides, connected to the rear wheels of the squeegee
(PHOTO D-20) , are used to adjust the slant with respect
to the plane, according to the axis perpendicular to the
machine’s operating direction.
To obtain a perfect adjustment, the rear strap, sliding
as it moves, bends in all points, forming an angle of
45° with the floor.
As the machine operates (advances), the knobs can
be used to adjust the slant of the straps: the slant
increases as the knob is screwed in and decreases as
it is unscrewed.
Squeegee drying must be uniform along the entire
drying line: damp patches mean that drying is insufficient;
turn the adjustment knobs to optimise drying.
7.1.6 SPLASH GUARD ASSEMBLY, DISASSEMBLY
AND ADJUSTMENT
The splash guard is equipped with an innovative comb
connection system. To lower or lift the splash guard off
the ground, just pull, detach the splash guard and then
attach it, by pressing it at the required level (PHOTO
A-6).
Use can also use a rubber mallet to insert it firmly into
position.
7.2 ACCESSORY ASSEMBLY, DISASSEMBLY AND
ADJUSTMENT (BRUSHES, SCRAPERS AND
ABRASIVE DISKS)
Never use the machine if brushes or scrapers and
abrasive disks are not perfectly installed.
Assembly:
Make sure that the brush plate is raised; otherwise lift
it by following the instructions provided in the specific
section. (PHOTO B-14)
To make sure that general switch is OFF.
Bring the brushes (or the guide disks equipped with
abrasive disks) near the connections, under the brush
plate; lower the washing plate and start the brushes
turning: the brushes/discs couple automatically;
Do not allow the length of the rows of brushes to