Krone Swadro 38 T Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 66

Krone Swadro 38 T Скачать руководство пользователя страница 62

Malfunctions - Causes and Remedies

62

Pos : 116.1 /Ü berschriften/Ü berschriften 1/P-T/Stör ung en - Ursac hen und Behebung @ 0\mod_1200296925180_78.doc @ 39459

16

Malfunctions - Causes and Remedies

Pos : 116.2 /Ü berschriften/Ü berschriften 2/P-T/Speziell e Sicherheits hinweis e @ 0\mod_1196660495760_78.doc @ 9134

16.1

Special Safety Instructions

Pos : 116.3 /BA/Sic herheit/Gefahrenhinweise/Ladewagen/Gefahr Wartung allgemein @ 0\mod_1199884069862_78.doc @ 36704

Danger! - When performing repair, maintenance or cleaning work on the machine, or in
the case of technical intervention, drive elements may start moving.

Effect: Danger to life, injuries or damage to the machine.
•

Switch off the tractor engine and remove the ignition key

•

Secure the machine and tractor against the possibility of rolling back.

•

Switch off the PTO and disengage it

•

After the repair, maintenance and cleaning work or technical interventions are completed,
mount all protective coverings and safety devices properly again.

•

Avoid skin contact with oils, greases, cleaning agents and solvents.

•

In the event of injuries or burns due to oils, cleaning agents or solvents, contact a
physician immediately.

•

All other safety instructions must also be followed to avoid injuries and accidents.

Pos : 116.4 /BA/Stör ung en - Ursachen und Behebung/Sc hwader/Tabellarisc he Auflistung Sc hwader 46 T @ 7\mod_1218454258483_78.doc @ 106966

Malfunction

Possible cause

Remedy

Rotor not working neatly

Raking height set too high

Set raking height lower

The working speed is too high.

Reduce the driving speed. Rough
estimate 8-10 km/h. For uneven
terrain and/or higher amount of
forage, it may be necessary to
drive slower.

Speed is too low

Increase the speed. Rough guide
450 rpm

Side rotor inclination set
incorrectly.

Change side inclination setting
(see chapter on operation entitled
"Side inclination setting of rotor
running gear").

Tine arm(s) crooked

Replace tine arms

High level of forage contamination Raking height set too low

Set raking height higher

Tine arm(s) bent

Replace tine arms

Swath width too large

Working width too large

Push swath former further in.

Speed is too low

Increase speed

===== Ende der Stüc kliste =====

«
...
60
61
62
63
64
...
»

Содержание Swadro 38 T



































































Отзывы:

Нет отзывов