Krone EasyCut F 320 Скачать руководство пользователя страница 18

Страница: 18 / 86

Safety

2.3

Basic safety instructions

Original Operating Instructions 150000802_00_en

2.3.13

Road safety

Dangers in road traffic

If the machine exceeds maximum dimension and weights specified by national law and if it is

not properly lit, other road users could be endangered when driving on public highways.

Before road travel, ensure that the maximum permissible dimensions, weights and axle

loads, supported loads and hitching loads which apply according to national law for driving

on public roads are not exceeded.

Before road travel, switch on lighting and ensure the proper function.

Danger when driving on road and field

Hitched and mounted machines change the handling characteristics of the tractor. The handling

characteristics depend for instance on operating state and ground. If changed handling

characteristics are not considered, the driver may cause accidents.

Observe measures for driving on road and field,

refer to page 48

Danger due to machine which is not prepared properly for road travel

If the machine is not prepared properly for road travel, serious accidents may occur on the

roads.

Before driving on roads, prepare the machine for road travel,

refer to page 49

Danger when cornering with mounted machine

When cornering, the tractor with mounted machine has a larger swivelling range. This may

result in accidents.

Consider the larger swivel range.

Consider people, oncoming traffic and obstacles when turning.

Danger of tipping over on slopes

The machine may tip over when driving on slopes. Thus there is a risk of accidents, serious

injuries or death. The risk of tipping over depends on many factors.

Observe measures for driving,

refer to page 48

2.3.14

Parking the machine safely

An improperly parked machine may move uncontrollably or tip over. People may be injured or

killed.

Park the machine on a horizontal and level ground capable of bearing the load.

Before adjusting, repairing, servicing and cleaning the machine, ensure that it is securely

positioned.

Note section “Parking the Machine” in chapter Driving and Transport,

refer to page 50

Unattended parking

Adults and especially children are at risk from an inadequately secured and unattended parked

machine.

Before parking it: Shut down and safeguard the machine,

refer to page 23

Содержание EasyCut F 320























































































Результаты поиска

Содержание EasyCut F 320

Отзывы:

Похожие инструкции для EasyCut F 320

Бренды по названию

Популярные бренды

Krone EasyCut F 320, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание EasyCut F 320

Отзывы:

Похожие инструкции для EasyCut F 320

Бренды по названию

Популярные бренды