KROHNE OPTISOUND 3020 C Скачать руководство пользователя страница 34

Страница: 34 / 52

6 Set up with the display and adjustment module

OPTISOUND 3020 C • Two-wire 4 … 20 mA/HART

30507-EN-190318

The values in bold font represent the data of the factory setting.
In HART multidrop mode, the current is constantly 4 mA. This value

does not change even in case of failure.

Current output

Characteristic: 4-20 mA

▼

Failure mode: 22 mA

▼

Min. current 3.8 mA

▼

In this menu item you simulate a user-defined level or pressure value

via the current output. This allows you to test the signal path, e.g.

through connected indicating instruments or the input card of the

control system.
The following simulation variables are available:

•

Percent

•

Current

•

Pressure (with pressure transmitters)

•

Distance (with radar and guided radar (GWR))

With Profibus PA sensors, the selection of the simulated value is

made via the "Channel" in the menu "

Basic adjustments

How to start the simulation:
1. Push

[OK]

2. Select the requested simulation variable with

[->]

and confirm

with

[OK]

3. Set the requested numerical value with

[+]

and

[->]

4. Push

[OK]

The simulation is now running, with 4 … 20 mA/HART a current is

output and with Profibus PA or Foundation Fieldbus a digital value.
How to interrupt the simulation:

→

Push

[ESC]

Information:

The simulation is automatically terminated 10 minutes after the last

pressing of a key.

Simulation

Start simulation?

If the function "

Reset

" is carried out, the sensor resets the values of

the following menu items to the reset values (see table):

Function

Reset value

Sensor address

126

Max. adjustment

0 m(d)

Service - Simulation

Service - Reset

Sensor-specific basic adjustment.

Содержание OPTISOUND 3020 C





















































Результаты поиска

Содержание OPTISOUND 3020 C

Отзывы:

Похожие инструкции для OPTISOUND 3020 C

Бренды по названию

Популярные бренды

KROHNE OPTISOUND 3020 C, Руководство пользователя

Результаты поиска

Содержание OPTISOUND 3020 C

Отзывы:

Похожие инструкции для OPTISOUND 3020 C

Бренды по названию

Популярные бренды