KRESS KU760, Инструкция по безопасности и эксплуатации

Страница: 9 / 12

9
Cut off saw KU760
side of the cutter must be facing outward (back to arm
(16)). If the direction of rotation is marked on the slice,
make sure that the direction of rotation of the slice is
the same as that of the spindle.
Install the external pressure plate (18), washers (19) and
hex bolts (20). Press down the spindle locking button
(22) until it is secured and tighten the hex bolt (20).
Slowly lower the movable shield to its original position.
3.Adjust the angle of the diagonal saw.
Be sure to pull out the plug before doing any
repairs to the machine.
The angle of the diagonal saw can be adjusted from
0 to 45 degrees. The fixing baffle (12) is marked with
commonly used angles. There are additional gears at 0
and 45 degrees.
Loosen the two fixing bolts (11) and (13) with wrench(9)
attached to the machine, and tighten the screw after
adjusting the angle.
4.Fixing the workpiece (see figure C)
Be sure to pull out the plug before doing any
repairs to the machine.
In order to ensure the safety of work, it is necessary to
fix the workpiece before using the machine.
Put the workpiece against the fixing baffle (12), push
the fastening screw rod (8) to the workpiece, and rotate
the screw handle (7) to clamp the workpiece.
Release the workpiece
Loosen the screw handle (7). Lift the unlock key (6) and
pull out the fastening screw rod(8).
5.Formal operation
Start/shut off (see figure D)
Press the switch (3) and press the switch self-locking
button (2), then release the switch, and then release the
self-locking button. At this time, the switch is locked in
working state. Re-press and loosen the switch to stop
the machine.
Operation instructions
Maximum workpiece size [mm]
Angle of the diagonal saw
Workpiece
shape
0° 45°
115 x 115 95x95
110 x 120 95x120
125 x 125 95x95
The machine should not be blocked by overload.
If the machine is operated with too much force, it will
not only reduce the power of the machine, but also
shorten the service life of the slices.
During cutting, the slices become very hot; they are not
touchable until they are cooled down.
Choose the appropriate slice according to the
workpiece.
Cutting depth
The cutting depth has been adjusted when the
machine leaves the factory. Generally speaking, if a
new 355 mm slice is used, it should not exceed the
lower plane of the base when cutting. If the chip has
been heavily worn, reduce the depth scale to balance
the gap.
When using new slices, it is necessary to adjust the
depth scale back to the original position at the time of
leaving the factory.
Correctly adjust the depth scale so that the
slice can not exceed the bottom plane of the
base when cutting the workpiece.
Adjust the cutting depth
Be sure to pull out the plug before doing any
repairs to the machine.
Use the attached wrench to loosen the cutting depth
adjusting bolt (14). Push the handle to adjust the arm
(16) to the desired position.
Turn the adjusting bolt (14) clockwise or
counterclockwise until the bolt head contacts the arm
housing.
Slowly raise the arm (16) and tighten the adjusting bolt
(14).
MAINTENANCE
Be sure to unplug the power cord before any
repair work on the machine.
No additional lubrication or special maintenance
is needed for your power tool. Do not use water
or chemical detergent to clean your power tool.
Wipe it with a dry cloth. Tools should be kept in dry
environment and keep the motor vent clean. Try not to
use it in dusty environment.
If the power cord is damaged, it must be replaced
by the manufacturer, a special service center, or an
professional person with equivalent qualifications to
avoid a hazard.