Krell Industries PHANTOM II Скачать руководство пользователя

Страница: 48 / 49

Inputs

2 pr. CAST via 4-pin bayonet connectors
2 pr. balanced via XLR connectors
3 pr. single-ended via RCA connectors

Tape input

1 pr. single-ended via RCA connector

Main outputs

1 pr. CAST via 4-pin bayonet connectors
1 pr. balanced via XLR connector
1 pr. single-ended via RCA connector

Subwoofer outputs

1 pr. balanced via XLR connector
1 pr. single-ended via RCA connector

Tape outputs

1 pr. single-ended via RCA connector,

buffered

Control inputs

1 RS-232 input via a 9-pin D-subminiature

connector

1 remote IR detector input via

a 3-conductor 3.5 mm connector

1 12 VDC trigger input via

a 2-conductor 3.5 mm connector

1 preamplifier link via an RJ-45 connector

Control outputs

2 individually programmable 12 VDC

trigger outputs via 2-conductor 3.5 mm
connectors (500 milliamps maximum
per output)

1 preamplifier link via an RJ-45 connector

Power output

1 phono power output (±20 VDC) for KPE

via a 9-pin D-subminiature connector

Input impedance

CAST: 25 Ohms
Balanced: 40 k Ohms
Single-ended: 20 k Ohms

Output impedance

CAST: >1 M Ohms
Balanced: 250 Ohms
Single-ended: 125 Ohms

Gain

12 dB (CAST or balanced output)
6 dB (single-ended output)

Volume control

Balanced, current-mode,
16-bit, discrete R-2R ladder

Input overload

CAST: 12 mA RMS
Balanced: 10 V RMS
Single-ended: 6.5 V RMS

Output overload

CAST: 16 mA RMS
Balanced: 16 V RMS
Single-ended: 8 V RMS

Frequency response

20 Hz to 20 kHz ± 0.02 dB
0.35 Hz to 720 MHz +0, -3 dB

Total harmonic distortion plus noise

Balanced Output:
<0.003%, 20 Hz to 20 kHz, 4 V RMS or
4 mA RMS

Signal-to-noise ratio

4 V RMS balanced or 4 mA RMS CAST output

Wideband, unweighted: >100 dB
“A” weighted: >109 dB

Power consumption

Standby: 60 W
Power on: 65 W
Power on, with KPE: 75 W

Dimensions

17.3 in.W x 3.8 in. H x 18.25 in. D
43.82 cm W x 9.7 cm H x 46.4 cm D

Weight

Shipped: 38 lbs., 17.2 kg
Preamplifier only: 23 lbs., 10.2 kg

Note

All operational features, functions, specifi-

cations, and policies are subject to change

without notification.

Specifications

Содержание PHANTOM II


















































Результаты поиска

Содержание PHANTOM II

Отзывы:

Похожие инструкции для PHANTOM II

Бренды по названию

Популярные бренды

Krell Industries PHANTOM II, Руководство пользователя для владельца

Результаты поиска

Содержание PHANTOM II

Отзывы:

Похожие инструкции для PHANTOM II

Бренды по названию

Популярные бренды