Krell Industries PHANTOM II Скачать руководство пользователя

Страница: 47 / 49

Return Authorization Procedure

If you believe there is a problem with your component, please contact your dealer,

distributor, or the Krell factory to discuss the problem before you return the com-

ponent for repair. To expedite service, you may wish to complete and e-mail the

Service Request Form in the Service Section of our website at:

http://www.krellonline.com

To return a product to Krell, please follow this procedure so that we may

serve you better.

Obtain a Return Authorization Number (R/A number) and shipping address

from the Krell Service Department.

Insure and accept all liability for loss or damage to the product during ship

ment to the Krell factory and ensure all freight (shipping) charges are prepaid.

The product may also be hand delivered if arrangements with the Service

Department have been made in advance. Proof of purchase will be required for

warranty validation at the time of hand delivery.

IMPORTANT

Use the original packaging to ensure the safe transit of the product to the factory,

dealer, or distributor. Krell may, at its discretion, return a product in new packaging

and bill the owner for such packaging if the product received by Krell was boxed in

nonstandard packaging or if the original packaging was so damaged that it was

unusable. If Krell determines that new packaging is required, the owner will be noti-

fied before the product is returned.

To purchase additional packaging, please contact your authorized Krell dealer, dis-

tributor, or the Krell Service Department for assistance.

To contact the Krell Service Department

TEL

203-298-4020, Monday-Friday

9:00 AM to 5:00 PM EST

FAX

203-795-2287

E-MAIL

[email protected]

WEBSITE http://www.krellonline.com

Phantom II

PRODUCT

MODEL NUMBER

SERIAL NUMBER

Содержание PHANTOM II


















































Результаты поиска

Содержание PHANTOM II

Отзывы:

Похожие инструкции для PHANTOM II

Бренды по названию

Популярные бренды

Krell Industries PHANTOM II, Руководство пользователя для владельца

Результаты поиска

Содержание PHANTOM II

Отзывы:

Похожие инструкции для PHANTOM II

Бренды по названию

Популярные бренды