Krell Industries PHANTOM II Скачать руководство пользователя | Manualshive

Страница: 34 / 49

background image

34

continued

Info

This function enables you to access information about the preamplifier software,

EEPROM, and PC Boards. The PC Boards are listed in the left margin, on this

page.

Enter the menu, then:

1.

Use the level control knob on the preamplifier front panel or up and down keys

(14) on the remote control to select:

INFO.

2.

Press the enter button on the preamplifier front panel or the enter key (6) on

the remote control

.

The front panel display (3) shows the software version num-

ber.

3.

Rotate the level control knob clockwise or press the up key. The front panel

display shows the EEPROM version number.

4.

Rotate the level control knob clockwise or press the up key again. The front

panel display shows the PC board version number.

5.

Press the enter button or key. Use the level control knob or the up and down

keys to scroll through the version numbers of PC boards, from the PC Boards

listed at left.

EEPROM

Electrically erasable programmable read-only memory. An erasable memory chip

used in the Phantom II to store menu selection information.

PC Boards

CONTROL

DISPLAY

ENCODER

MAIN L

MAIN R

POWER CONN

POWER SUPP

DIG CONN

«
...
32
33
34
35
36
...
»

Содержание PHANTOM II


















































Отзывы:

Нет отзывов

Похожие инструкции для PHANTOM II

MINAS-BL GP series

Бренд: Panasonic Страницы: 9

Бренд: Pangea Audio Страницы: 7

Бренд: Make Noise Страницы: 10

Бренд: Waterfall Audio Страницы: 34

Бренд: Peavey Страницы: 14

Бренд: Richie Kotzen Страницы: 12

Valvestate VS230R

Бренд: Marshall Amplification Страницы: 7

Бренд: resi-linx Страницы: 4

Бренд: Sansui Страницы: 24

Бренд: NAD Страницы: 12

Бренд: Tekbox Страницы: 10

Бренд: Boss Audio Systems Страницы: 19

Tube Location GA-9

Бренд: Gibson Страницы: 1

Бренд: JBL Страницы: 22

Nova PA-600 Operation manual

Бренд: EarthQuake Страницы: 12

Бренд: Sansui Страницы: 32

Бренд: NAD Страницы: 2

Бренд: OPTEX FA Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды