Krell Industries KAV 3250 Скачать руководство пользователя

Страница: 30 / 32

Krell KAV–2250 and KAV–3250

Specifications

KAV–2250

FREQUENCY

20 Hz to 20 kHz

+0 dB, -0.09 dB

RESPONSE

0.25 Hz to 170 kHz

+0 dB,

-3 dB

SIGNAL TO NOISE
RATIO
“A” WEIGHTED

>112 dB

TOTAL HARMONIC

1 kHz

< 0.03%

DISTORTION (THD)

20 kHz

< 0.20%

GAIN

25.7 dB

INPUT IMPEDANCE

100 kOhms

INPUT SENSITIVITY

2.32 Vrms

OUTPUT VOLTAGE

Peak to Peak

127 V

RMS

45 V

OUTPUT POWER

EACH CHANNEL

8 Ohms

250 W

4 Ohms

500 W

BRIDGED

8 Ohms

1000 W

POWER

Standby

35 W

CONSUMPTION

Idle

80 W

Max.

2000 W

INPUTS

2 single-ended via RCA connectors

2 balanced via XLR connectors

OUTPUTS

2 amplifier channels via five-way binding posts

REMOTE CONNECTORS

12 VDC Out (12 V trigger) via a 3.5 mm connector

12 VDC In (12 V trigger) via a 3.5 mm connector

DIMENSIONS

17.3w x 5.6h x 17.1d in.

43.8w x 14.3h x 43.4d cm

WEIGHT

SHIPPING

74.0 lb., 33.5 kg

UNIT ONLY

64.0 lb., 29.0 kg

All operational features, functions, specifications, and policies are subject to change without notification.

Содержание KAV 3250

































Результаты поиска

Содержание KAV 3250

Отзывы:

Похожие инструкции для KAV 3250

Бренды по названию

Популярные бренды

Krell Industries KAV 3250, Руководство пользователя для владельца

Результаты поиска

Содержание KAV 3250

Отзывы:

Похожие инструкции для KAV 3250

Бренды по названию

Популярные бренды