Krautzberger 0920-090-2357 Скачать руководство пользователя страница 11

Страница: 11 / 19

Type

RA-2 HV3

Operating Instructions

DOK-208-GB.doc

No. 0920-..,

0921-...

Air nozzles

standard design:

brass, nickel plated

special

design:

brass,

PTFE

coated

Special equipment

Material needle with puncture pin:

to prevent the material nozzle from becoming blocked due to bonding of material particles,

this material needle is fitted with a cylindrical pin (puncture pin) at the tip in front of the

sealing cone.

Pneumatically adjustable needle path limiter:

this is for the purpose of opening and closing the material throughput cross-section in two

stages. This is of advantage if there are frequent changes between circular jet (low material

requirements) and flat jet (generally higher material requirements) during the spraying

process.

Parts in contact with the material

Standard version

Version on request

Part designation

Made of

Art. no.

Made of

Art. no.

Screw connection

plastic

6903-0320-0807 stainless

steel

6903-030-0846

Screw connection

plastic

6903-030-0725 stainless

steel

6903-030-0853

Double nipple

brass

6902-030-2230 stainless

steel

6920-040-2349

Gasket

UHMW-PE

0902-010-0364

PTFE

NBR (for glaze)

0902-010-0365

0902-010-0186

Gasket

Viton

0909-010-0145

---

---

Gasket

Viton

0909-010-0497

---

---

Adapter

PA-6

0902-080-0273

0909-080-2325

0909-080-1253

Material nozzle

stainless steel 0902-050-....

tungsten

carbide

0902-050-....

Material needle

stainless steel 0902-070-....

tungsten

carbide

0902-070-....

Содержание 0920-090-2357




















Результаты поиска

Содержание 0920-090-2357

Отзывы:

Похожие инструкции для 0920-090-2357

Бренды по названию

Популярные бренды

Krautzberger 0920-090-2357, Инструкция по эксплуатации и список запасных частей

Результаты поиска

Содержание 0920-090-2357

Отзывы:

Похожие инструкции для 0920-090-2357

Бренды по названию

Популярные бренды