background image

6 Installation, removal and connection

6.3 Installing the EET in OMG

6.3 Installing the EET in OMG

Personnel qualification:

o

Electrician

Personal protective equipment:

o

Work clothing

Aids:

o

Torque wrench

 WARNING

Risk of injury through escaping medium.

Media can be hot, poisonous, combustible and caustic.

► Before installing the sensor, switch off the system and depressurise it.

► Wear personal protective equipment at all times during operation. Pay attention to face protection.

► Collect any escaping medium safely and dispose of it in an environmentally compatible manner in

accordance with the applicable local regulations.

ATTENTION

Incorrect installation destroys the sensor

► Select the correct installation location.

X

X

1

1

2

2

OMG 32

OMG 52

1.

 Select the correct bore and remove the screw plug from the sensor bore.

2.

 Clean the sensor bore. No foreign bodies should penetrate the flowmeter 

2

 or piping system.

3.

 Select suitable sensor 

1

Ä

 Technical data, Page 5.

4.

 Screw the sensor into the sensor bore as far as it will go, maximum tightening torque 30 Nm.

5.

 Connect the sensor cable, observing the connection diagram. 

Ä

 Technical data, Page 5.

6.4 Installing the EET in OMP

Personnel qualification:

o

Electrician

Personal protective equipment:

o

Work clothing

Aids:

o

Torque wrench

 WARNING

Risk of injury through escaping medium.

Media can be hot, poisonous, combustible and caustic.

► Before installing the sensor, switch off the system and depressurise it.

► Wear personal protective equipment at all times during operation. Pay attention to face protection.

► Collect any escaping medium safely and dispose of it in an environmentally compatible manner in

accordance with the applicable local regulations.

10

OII 08en-GB Edition 2021-07

Operating instructions

Содержание EET 32

















Отзывы: