background image

30

  OPERATING INSTRUCTIONS

WARNING

Do not operate appliance with the glass front removed, cracked, 

or broken. Replacement of the glass should be done by a licensed 

or qualified service person.
Under no circumstances should any solid fuel (wood, coal, paper, 

cardboard, etc.) be used in this appliance.
Children and adults should be alerted to the hazards of high 

surface temperature and should stay away to avoid burns or 

clothing ignition.

CAUTION

Clothing or other flammable material should not be placed on or 

near the appliance.
Young children should be carefully supervised when they are in the 

same room as the appliance. Toddlers, young children and others 

may be susceptible to accidental contact burns. A physical barrier 

is recommended if there are at risk individuals in the house. To 

restrict access to a fireplace or stove, install an adjustable safety 

gate to keep toddler, young children and other at risk individuals 

out of the room and away from hot surfaces.

WARNING: 

If you do not follow these instructions exactly, a fire or explosion may result causing property damage, 

personal injury, or loss of life.

STOP! Read all the safety information above on this page. 
Press the wireless remote OFF button. 
Turn off all electric power to the appliance. 
This appliance is equipped with an ignition device which 

automatically lights the pilot. Do not try to light the pilot 
by hand.

Locate the manual valve installed by your qualified service 

technician.

Turn the manual valve clockwise to 

the OFF position. 

Wait five (5) minutes to clear out 

any gas. Then, 

smell for gas, including near the floor. If you smell gas, 
STOP! 
Follow ‘B’ in the safety information above. If you do not 
smell gas, go to the next step. 

Turn the manual valve counterclockwise  

to the ON 

position. 

Turn on all electric power to the appliance. 
Press the wireless remote ON button. 
If the appliance will not operate, follow the instructions, 

“To Turn Off Gas To Appliance” and call your service 
technician or gas supplier. 

OPERATING INSTRUCTIONS

NOTE

When this fireplace is initially lit, condensation will appear on the glass. This is normal in all gas fireplaces and will disappear after 
several minutes. A paint smell will occur during the first few hours of burning. It is recommended to leave the fan off during this period to 
help speed the paint curing process. This fireplace may produce noises of varying degree as it heats and cools due to metal expansion 
and contraction. This is normal, and does not affect the performance or longevity of the fireplace.

A. 

This appliance is equipped with an ignition device which 

automatically lights the pilot. Do not try to light the pilot by 

hand. 

B. 

BEFORE OPERATING

 smell around the appliance area for 

gas. Be sure to smell next to the floor because some gas is 

heavier than air and will settle on the floor. 
WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.

•  Do not touch any electric switch; do not use any phone 

in your building.

•  Immediately call your gas supplier from a neighbor’s 

phone. Follow the gas supplier’s instructions. 

•  If you cannot reach your gas supplier, call the fire 

department. 

C. 

Use only your hand to turn the gas control manual valve. 

Never use tools. If the valve will not turn by hand, do not 

try to repair it; call a qualified service technician. Force or 

attempted repair may result in a fire or explosion. 

D. 

Do not use this appliance if any part has been under water. 

Immediately call a qualified service technician to inspect the 

appliance and to replace any part of the control system and 

any gas control that has been under water. 

ON/OFF 

ON

OFF

1. 

Press the wireless remote OFF button.

2. 

Turn off all electric power to the appliance if service is to 
be performed. 

3. 

Locate the manual valve installed by your qualified service 
technician.

4. 

Turn the manual valve clockwise 

to OFF position. 

FOR YOUR SAFETY READ BEFORE OPERATING

TO TURN OFF GAS TO APPLIANCE

10.0  OPERATING INSTRUCTIONS

Содержание TRF-41 LOG














































Отзывы: