42 OPERATING INSTRUCTIONS
Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces
#SP-34 LE & MV R.5 January 2020
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING
Do not operate appliance with the glass front removed, cracked, or
broken. Replacement of the glass should be done by a licensed or
qualified service person.
Under no circumstances should any solid fuel (wood, coal, paper,
cardboard, etcetera) be used in this appliance.
Children and adults should be alerted to the hazards of high surface
temperature and should stay away to avoid burns or clothing ignition.
CAUTION
Clothing or other flammable material should not be placed on or near
the appliance.
Young children should be carefully supervised when they are in the
same room as the appliance. Toddlers, young children and others
may be susceptible to accidental contact burns. A physical barrier is
recommended if there are at risk individuals in the house. To restrict
access to a fireplace or stove, install an adjustable safety gate to keep
toddlers, young children and other at risk individuals out of the room
and away from hot surfaces.
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal
injury, or loss of life.
A.
This appliance has a pilot which must be lighted by hand. When
lighting the pilot, follow these instructions exactly.
B.
BEFORE LIGHTING smell around the appliance area for gas. Be
sure to smell next to the floor because some gas is heavier than
air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in
your building.
• Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire
department.
C.
Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand,
don’t try to repair it, call a qualified service technician. Force or
attempted repair may result in a fire or explosion.
D.
Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control that has been under water.
LIGHTING INSTRUCTIONS
1.
STOP! Read all the safety information above on this page.
2.
Set thermostat to lowest setting (if applicable).
3.
Turn off all electric power to the appliance.
4.
Open the control compartment access panel.
5.
Push in gas control knob slightly and turn clockwise
to
“OFF”.
NOTE: Knob cannot be turned from “PILOT” to “OFF” unless
knob is pushed in slightly. Do not force.
6.
Wait five (5) minutes to clear out any gas. Then, smell
for gas, including near the floor. If you smell gas, STOP!
Follow ‘B’ in the safety information above. If you do not smell
gas, go to the next step.
7.
Locate pilot - follow metal tube from gas control. The pilot is
located inside the combustion chamber.
8.
Push in gas control knob slightly and turn counterclockwise
to “PILOT”.
9.
Push in control knob all the way and hold. Press the piezo
igniter button repeatedly until the pilot is lit and continue to
hold in the gas control knob.
10.
Hold the gas control knob in for one (1) minute after pilot is lit.
Release knob and it will pop back up. Pilot should remain lit. If
it goes out, repeat steps 5 through 10.
• If the knob does not pop out when released, stop and
immediately call your service technician or gas supplier.
• If the pilot will not stay lit after several tries, turn the gas
control knob to “OFF” and call your service technician or gas
supplier.
11.
Turn the gas control knob counterclockwise
to “ON”.
12.
If you desire only the pilot flame to be lit and not ignite the
main burner, push the gas control knob in slightly and turn
clockwise to ‘PILOT’.
13.
Set control compartment access panel back into position.
14.
Turn on all electric power to the appliance.
15.
Set thermostat to desired setting (if applicable).
TO TURN GAS OFF TO APPLIANCE
1.
Set thermostat to lowest setting (if applicable).
2.
Turn off all electric power to the appliance if service is to be
performed.
3.
Open the control compartment access panel.
4.
Push in gas control knob slightly and turn clockwise
to
“OFF”.
5.
Set control compartment access panel back into position.
10.2 Lighting Instructions (#SP-34-MV)
•
When this fireplace is initially lit, condensation will appear on the
glass. This is normal in all gas fireplaces and will disappear after
several minutes.
•
A paint smell will occur during the first few hours of burning. It
is recommended to leave the fan off during this period to help
speed the paint curing process.
•
This fireplace may produce noises of varying degree as it heats
and cools due to metal expansion and contraction. This is normal,
and does not affect the performance or longevity of the fireplace.
GAS CONTROL
KNOB SHOWN IN
“OFF” POSITION
