background image

15 | 

P a g e

 

 

MAINTENANCE OVERVIEW 

 

Safety Practices 

 

 

1. Check your fuel supply regularly and allow suitable time for deliveies 

 try not to run out of fuel  

2. Check the ash box and empty regularly.  

3. Inspect chimney, flue pipes, flue pipe joints, and flue pipe seals regularly to ensure that smoke and 

flue 

gases are not drawn into, and circulated by, your home‟s air circulation system. If you observe 

rust or any smoke leakage, replace the pipe immediately.  

4. Exercise the safety relief valve at least once a year.  

5. Check the water pressure is between 1 and 2 bar 

 if too low top up system with more water.  

6. 

DO NOT 

clean heating system surfaces when the unit is hot. Wait until the unit cools and then 

clean with soap and water.  

 

ATTENTION 

 

This work may only be performed by certified specialists or by Kozlusan customer 

service personel. The boiler requires a minimum of 1 anual service by certified personel 

to maintain warranty guarantee! 

Periodical Maintenance 
 
 
                                                             Brushing Burnpot 

 

 
 
 
 
 
 
 
 
 



Take out front door cover      Unloose the star handles        Remove burnpot door   

 

 




 
    Brush inside the burnpot and remove the flue ashes in the combustion chamber with vacuum cleaner 

Содержание Propel 25


























Отзывы: