Korenix JetLink 1102 Скачать руководство пользователя страница 49

Страница: 49 / 52

JetLink 1102/

JetLink 1302 User Manual

The following table describes the items in the previous figure.

If you want to disable the password protection, change the password to the default
option None (leave the password column blank). Be sure apply and reboot the system
(

System Management

Apply Configuration

) to save the updates.

3.6.2

Backup Manager

The Backup Manager page allows you to backup configuration from the device or
restore configuration file to the device.

To access this page, click

System Management

Backup Manager.

Figure 3.20 System Management > Backup Manager > Backup Manager

The following table describes the items in the previous figure.

Figure 3.21 System Management > Backup Manager > SD Card Backup

Содержание JetLink 1102





















































Результаты поиска

Содержание JetLink 1102

Отзывы:

Похожие инструкции для JetLink 1102

Бренды по названию

Популярные бренды

Korenix JetLink 1102, Руководство пользователя

Результаты поиска

Содержание JetLink 1102

Отзывы:

Похожие инструкции для JetLink 1102

Бренды по названию

Популярные бренды