Korea Nakajo NSM-25G0MW Скачать руководство пользователя страница 4

Precautions

4

Warning(When installing)

Ice making dish

Low ice container

material hose

Ice making material container

Over 10℃

1

Preparation

1-1. Precautions and warnings for safety

When electric cord is damaged, in order to
prevent danger, it should be repaired by
service technician

If not, it may cause fire, 

electric shock or the
machine malfunction

X

When washing the machine, please use
neutral detergent only and remove
moisture after cleaning

There is a risk of fire or electric

shock. It may also cause the

product malfunction

No thinner, 

organic agent,

petrol or gas

When not using the machine, please keep ice
making material containers(ice making dish and
material supply hose) clean for storage

It may cause bad quality or odor of the water for ice making

When storing the machine during winter, please
avoid temperature lower than 0 Celsius degree

If water in cooling water coil and pressure valve is
frozen, there may be freezing-burst

If not, please remove water in cooling coil and then store it

In order to remove ice in drum, if you use sharp
instruments such as drill or knife for impressing
or scratching, cooling agent will be leaked or ice
quality will be worse

In the temperature between 10~35 Celsius degrees,
please install the machine. Water temperature for
supply should not exceed the range between 5~25
Celsius degrees

In case of out of temperature

degrees, it may cause damages 
or malfunctions

Depending on temperature or

humidity, amount of ice making 
can be different

Water pressure of cooling water should be
between 1 and 6 bars.

If water pressure is higher than 

6 bar, please install pressure 
decrease device

When it is less than recommended
pressure, please install pressure
pump. Please contact to the service
center(pressure pump is an option.)

Less than 6bar

Please install the machine horizontally

Please keep balance

between front and back
and right and left within  
2mm. (It may cause 

uneven ice quality)

For connecting drainage hose, please
install it for free flow of water.

If drainage is not well done,
water will overflow or standing 
water may cause unhealthy use 

Содержание NSM-25G0MW

















Отзывы: